Search results

Selling my brand new not even out of the shipping crate from Freddie Brown. Comes with the following: 4R75 with wide gear set, transbrake with full manual VB, Auto Reset controller, dipstick and tube, Crossmember, crossmember bracket and trans mount, trans cooler with braided lines and...

Selling my complete auto swap that is brand new not even out of the shipping crate from Freddie Brown. Comes with the following: 4R75 with wide gear set, transbrake with full manual VB, Auto Reset controller, Flexplate and bolts, dipstick and tube, Crossmember, crossmemeber bracket and trans...

Pair of Corbeau FX1 suede seats with mounting brackets and sliders for 04-up Mustang. 6 months old, no rips, tears, stains or imperfections. $600 plus shipping, if applicable. [email protected] Would prefer local sale, because I don't have boxes, but might be able to locate some if needed.

2011 Shelby GT500 with 14k miles, had 10 when I bought it in 2011. BMR K-Member, a-arms, Springs and Strange single Adj struts ARH 1-7/8" headers with 3" H-pipe and Magnaflow 3" Street exhaust (new) Kenne Bell 2.8L supercharger, KB Dual 75mm throttle body, Inlet is Autographed by Carol...

Selling my complete auto swap that is brand new not even out of the shipping crate from Freddie Brown. Comes with the following: 4R75 with wide gear set, transbrake with full manual VB, Auto Reset controller, Flexplate and bolts, dipstick and tube, Crossmember, crossmemeber bracket and trans...

Ok guys, got my new Corbeau FX1 seats installed. Searched numerous sites on this issue. Used a 2 ohm, 1 watt, 5% resistor and still get the light. Yes, I installed the seat position sensor on both seat rails, and yes I installed the OCS bladder in passenger seat. But still get the light on...

Well, decided to do it. Contacted FB trans and talked to Fred and he is hooking me up with 4R70 with trans brake and all the goodies.:banana: Couldn't be more excited!!! My Corbeau FX1 seats will be here tomorrow, so I'll post up some pics when I get them installed. Lots of transformation...

Ok been having issues and I am running out of ideas. Car is a 2011 with BMR k-member, A-Arms, lowering springs, strange adj struts, 17" weld fronts, no sway bar, Steeda bump-steer. The car has a bad wobble at about 65 mph. I've balanced the front tires and had an alignment done. Tire...

Got tre car dyno'ed, made good power, ran great for a few days. Drove it Monday and Tuesday with no issues, then last night go to start it and it just cranks with no attempt to fire at all. Battery is perfect, I checked all the BAP fuses and all good there.... any ideas? I'm sure it is...

Used KB street dual boost a pump off my 2011 GT500. In perfect working order and comes with all installation hardware/wiring/ and instructions. I had to move up to a competition unit, so simply took this one off and replaced with the bigger one. $335 shipped. Will post pics this evening...

Stock injectors off my car.... 10k miles. In great shape, no defects or issues, just went bigger. $200 shipped. email for info or pics at [email protected] I made 730rwhp with these and a BAP.

Stock injectors off my car.... 10k miles. In great shape, no defects or issues, just went bigger. $200 shipped. email for info or pics at [email protected]

Brembo front brakes off my 2011 GT500 for sale. Comes with calipers, rotors, pads, dust shield, and brake lines. Pads and rotors have approximately 10k miles on them and still look new. Car has never seen rain and only gets driven on the weekend. Nothing wrong with any of the components, all are...

So I am changing to SS brake lines and need to know what size the factory fitting is.... meaning, I have a -3 90* to straight -3, but the factory line looks way bigger than -3. Any ideas?

Have the Lethal 3" off-road x-pipe off my car, has about 2k miles on it. Tried selling local but no interest, so I will figure out how to ship this thing. $200 plus shipping.

Anyone here narrowed the rear end of these cars? I'm going to do it over the summer, but was wondering if anyone has done it and maybe even a little minitub at the same time? My intentions are the try to make the rear end a little more bullet proof before I go torture it at the drag strip...

Brand new BMR K-member brace. Bought it, took it out of the box, realized it would not fit with my radiator support. No scratches, all bolts still in sealed bag. $125 shipped.

off my 2011 GT500. Nothing wrong, tips look perfect.... changed to Magnaflows. $175, buyer pays shipping. [email protected]

I can only afford do to one or the other this winter. Here is the dilema: Change cams, injectors, and long tubes or Long tubes (I have them already), injectors, k-member/a-arms, and lightweight front brakes. Which one would you do? This is on my 2011 with 2.8KB.... made...

Has anyone done a custom exhaust yet? Or just done a custom axle back? I cannot find anything that sounds quite like I want and one that I like (Magnaflow Street series) they want 750 for an axle back.:fm: I have a MIG and am capable of fabricating something, but not sure what to do. I...

Pulled it off my car to replace with C&R unit. Has approx 10k miles on it. $150 plus shipping. Will post pics tomorrow. [email protected]

I have the stock SVTPP front struts off my car for sale, if interested. Make reasonable offer plus shipping. They have approx. 9k miles on them. Also have the stock front and rear springs for the car as well, make offer. Email [email protected].

I took the stock radiator mount, sway bar, and under tray off my 2011 GT500. If anyone is interested, make me an offer. Email to [email protected]. Will snap some photos tomorrow and post up.

I've read a few threads here and there talking about why it doesn't work in our cars, but no one is ever specific.:shrug: There is one gentleman who just recently did it, and now I am seriously considering it. Can anyone tell me specific reasons not to do it? I'm not worried about what the...

Just wanted to give you guys a heads-up on the struts for the 2011's. I wanted to change mine to something adjustable. Ordered some for my 2011 GT500, they got here and would not fit. Turns out that my car has a manufacturers date of 03/10 on it and they actually used the 2010 front struts...