Who's done it ? I've got a UPR tubular K member and really don't want to tear the suspension apart to remove it again... Loosensing motor mounts and lifting the engine a little isnt a big deal but I'd like to do it with the k member in the car still. looks roomy with the stock junk gone, has...
Hey,
So heres what I've got. 2003 Mach with Koni yellows and UPR coil over conversion and MM CC Plates. Issue being the spacer setup. On the bottom side i can do one big spacer, then on top one spacer and that allows the nut to fully engage the threads. However it appears the coil spring...
Hey,
Pretty new to this, took a ton of pics at the track yesterday and got them edited and I've created a watermark within lightroom, when i go to export a photo i select watermark and choose the one i had made. However once exported the watermark is nowhere to be seen. What gives ?
Quick one, see a lot regarding lowering a car with coil overs and using fox struts. How low are we talking ? My car wont be super low, basically need to match my rears to get rid of the 4x4 look. After doing my rear suspension and ditching the lower iso's it dropped it a little more. (SRA its...
Not a big gamer but with no cable net available in my area I'm limited to single player mode on games. I'm pretty excited about a big open map shooter, anybody got it on pre order. I think I might tonight since I know I'm buying it for sure why not pre order and get the extra content (campaign...
So, it's well known 15x10 will fit with grinding. How about 15x8, what's required there? I'm looking at drag stars. And also what's required to fit the 275/60r15 out back?
So im tossing around the idea of headers on my Mach 1 and since the Mach sections slower than the cobra section and the info im looking is going to be the same between the cars. It's an 03 Automatic Mach. Narrowed my choices between kooks and ARH.
If i go kooks it'll be the 1 5/8" with there...
Hey, I have an 03 mach 1 but figure more people here have separators. I have a upr billet separator but I cannot figure where it would fit best. So just wanted to see pics of where you guys have mounted yours. This would be for the drivers side of the engine. I have a jlt pre filter on the...
Its been a while for me and ive having a hard time remembering. Now these questions are referring to stock spoilers.
99/00 spoilers, the hoopish looking one everyone hates. Does it use the same mounting hole configuration as as the 01-04 spoilers like that my mach has. Could one pop off the...
Hey guys, I got a set of the 17x4.5"s delivered today. Just wondering if most guys run these or the sve wheels ? The race stars are the direct drill but still require the special lug nut and washer. as to where the sve uses the standard acorn nut. Just wondered what everyones preference was and...
Hey, so with the window switch, not using a tach adaptor and running as 1 cylinder. Are you tapping off a wire directly from the a coil pack or going to the computer under the kick panel ?
Anyone actually using the bottle jackets. They're not the cheapest things and was wondering if its really nessecary. One of the things where I r already got the window switch remote opener billet bracket heater purge and blow down do I'm debating do I bother finishing it off with a jacket or no
Was about to place an order on a few things including gauges was set on the innovate mtx series but see a lot of people trashing the lc1 I'm just looking for opinions on a wideband. I like the fact I could swap the rings and face to match the silver w/white face gauge I'll be using with it. Is...
some of you may have seen this already but i like multiple opinions,
Just trying to figure out what all im going to need right now. My car is an 03 auto and I'm going to hit it with a 100 shot as from the reading ive done it looks to be a pretty safe deal.
But what about fuel ? It's going...
I've got an 03 mach and was wondering if anyone here with machs or the earlier cobras might be spraying, i was looking at a couple kits and just wondered what most guys prefer ?
I see and was suggested this proton kit,
http://www.nitrousexpress.com/20421-...lb-bottle.html
Cant...
I'll start from the beginning with this.
Friend of a friend moved into a house, found a enduro/dirt bike sitting out in the shed. Appeared to have been sitting for quite some time and assumed the previous owners just didn't want to bother with it and left it ( about 5 years ago.)
My friend...