Search results

wish I saw this before I ordered a pillar!. I sent it straight to alans shop. like you said great guy to deal with!

I saw that I might have to do that route if I cant find one already done

I am looking for a sos dual guage a pillar pod for a 04 in good condition. Shoot me a dm or leave a comment here thanks!

trying to find some 315 or 305 r888 tires in 18's. with them being discontinued I have had no luck finding a set. shoot me a pm if you have a new set you want to sell.

what head cooling mod is that?

I usually feel the same about my cars until I add a good set of wheels to it. Then it changes my mind and I start to love it

correct me if I'm wrong but I don't think it will pass with a aftermarket pulley?

b

looking to trade my new style race handle from mgw for a older blue handle. let me know if anyone has one laying around they would like to swap with.

Looking to buy a old orange mgw handle. Not a fan of the new style handle and trying to switch it up.

I was wondering if I were to buy a different set of mufflers if I can just unbolt the stinger muffler and replace it with a magnaflow. I don't want to weld them in and if I can just bolt them up how the stingers are in? Has anyone done it?

well i am going to be in the market for a 03 cobra and am looking in locations outside of california that have snow. Since California doesn't really snow unless you are in the mountains i never worry about rust. What are some key locations to look for rust on the 03 cobra. i want to go look at a...

looking to buy a 03/04 cobra with a clean title. Under 75k miles and not looking for extremely low mile ones or ones that are build. basic bolt on are fine as long as it passes smog. Anything but yellow or black and no verts. i am located in ventura county california but would drive to states...

recently my cobra started smoking on start up after driving it and letting it sit. it happens if i get on it a little (like only up to 4k rpms) and then park it and let it sit for a few hours. recently i also been seeing smoke when i come to a stop. it does smell like somthing is burning when i...

so i recently bought a iac restrictor plate that worked fine. i had to replace my iac because my old one was making my car idle bad and when i put the new one on it does not work the same. when i clutch in the rpms will hang at 1100 until i completely stop and then they will drop to 1000 rpm...

so i had this squeak coming from both wheels usually at low speeds and bought new wheel bearings and hubs. i had ford press them in and put them on and after some driving it came back almost the same as it was before. i have no idea what else could be making the squeak sound. any ideas?

my idle has been getting worse and dont seem to know what is causing it. i changed my spark plugs and cleaned the MAF and it is still the same. It is worse when i am warmed up. i notice sometimes when i shift the rpms still go up when the clutch goes in and fully off the gas. any ideas...

looking for a 2003/2004 cobra wing in good condition. would like to buy the whole trunklid if you have that as well. i am located in ventura county. shoot me a pm

looking for a 2003/2004 cobra wing in good condition. would like to buy the whole trunklid if you have that as well. i am located in ventura county. shoot me a pm

i have been checking to see when the anthracite 18 inch fr500s will be in stock. it said the 20th of December then changed to soon. when do you thik they will come in?

i am trying to figure out if i have a actually have borla atak catback. it came on the car and the muffler just says borla on the side. they were extremely loud but i am going to be selling them and want to be 100% sure. so if anyone has borla atak for 99-04 could you post a picture of the muffler.

right now im running all 17x9 rpf1s and was looking to switch to 18 rpf1s. will 18.9.5 with 15mm offset and 18x10.5 with 15 mm offset sit flush in the front and in the rear with irs?

i can not seem to find header to midpipe bolts anywhere. i am going to be installing a new midpipe on and just want some backup incase i strip a bolt

well i have two new hubs for my rear and 3 inch arp studs. i am trying to decide if i should press them in my self and how i would do that or should i just take it to a shop. they are part #100-7703 and i heard that they require some work to get them to go in. i am just really worried about...

thinking of buying the head cooling kit and was wondering how hard of a install it is. i have not done anything with engines before so this is a first and with it being my daily driver how long do you think it will be down for? i cant decide with one to get, theo ne for the top of the heads or...