sorry everyone, I have decided to take down my post on cars.com for a while. buyers noted some issues that need to be fixed before I post back up. I do intend to sell it.
ok havent gotten to it yet guys. that is a lot of 6's, Bullshitisay, but not close! It is negotiable. In perspective I paid 24K in 2008 with 29K miles, and have invested 11K and it runs great. Wish you could test drive it here and see for yourself.
I have checked other listing with similar mods...
I will try to do this later today. I am at work. there are 2 tiny dings. One in the front driver fender, and one near the rear trunk. Both were there when I bought the car.
Pete Johnson at Performance Dyno in NH tuned it several times, you could call him . It was also tuned once at Quintin Brothers in Burlington, VT, but went back to Pete for the final tunes. The paint is in good condition, a few small pits from normal driving in the passenger side fender. body is...
the mileage is correct, why would you say that? the pedals are not worn. they are practically new. And it has not been beat to hell, I have taken really good care of the car. In 10 years it has only seen the track twice. If you invested 11k in parts, you would take care of it too.. I can provide...
yeah! I went back and read all these posts! it all just makes me laugh now..
Pioneer AVH-P44000BH 6x8 JBL front, 6x9 JBL rear, JBL 8 inch Sub in back, JBL GTO 804 amp, JBL CS300.1 mono amp
Have owned this Cobra for 10 years. Reliable and powerful 93 tune 619/546
Check all photos and specs on cars.com
Https://www.cars.com/vehicledetail/detail/739508301/overview
Sent from my SM-G930V using the svtperformance.com mobile app
I did an external oil cooler over the winter, M6881-A5 with a Derale 10x13 with fan in the drivers side wheelwell. It has a 180 degree oil thermostat, and 190 degree thermo switch on the out side of the cooler. From the coolant side I necked down from 2 inches to 1.5 at the thermostat. The temp...
I have strange coilovers with Tokico D-spec struts, and Team-Z cc plates. I installed the passenger side without issue. I went to the drivers side and starting putting the coilover together, and the top cap, or whatever they call it, the last piece.. gets stuck on the strut threads.. Should that...
I need a driveshaft yoke on the pinion end for 04 cobra driveshaft ; Ford does not sell it seperate. The smaller yoke I have is damaged along with the u-joint.. thx!
FS: Ported Eaton
Whipple 2.9 build is complete, so I want to sell or trade parts I no longer need. swapped at 32k miles, car made 482/464 on stock engine, with this blower.All prices are shipped.
Best Offers now!
Ported Eaton w2.8 pulley/stock TB/plenum(unported) 450.00 SOLD
2 stacked FPDMś...
I have recently rebuilt the 8.8 in my 04 cobra, Eaton Truetrac, 31 spline Moser axles, new 3.73 ring/pinion, solid spacer,all new bearings. Not for the fun of it, because it exploded after the 2.9 whipple was installed. Ha ha!
My question is the pinion preload. I set it at 20in/lbs. It seems...
I happened to buy 2 gauges at Speedhut at the right time.. during a sale! gauges are 10% off, the price is marked for each gauge at the sale price. In addition, for buying 2 gauges you get additional 5%, for 3 gauges 10%, 4 guages 15%. I didn't realize until I talked to someone on the phone...
I posted yesterday about running at the track and the car stalling on me at the end of the run; I had the code P0193, seemed likely the FRPS, so I replaced it, cleared the code and it didn't show back up..
I try to start the car and it is turning over easy, but just won't start.. There was a...
I ran at NE dragway Friday night, on the second run I hit the rev limiter in 3rd, slightly. When I threw it in neutral and slowed down the car stumbled and died...I have the code P0193.
Car turns over easy, but will not start, ( flooded too) It was a long night! And a long tow back to Vermont...