have a local guy with a very low mileage gen3 2.9 off his 09 he purchased back in 2017, car got wreaked and he had the tow yard pull the blower off for him but unfortunately he or the shop pulling it didn't have much of an idea what all the necessary hardware and other things needed in the kit...
Selling for a friend it's fully ported by Jay Blwn04SVTcobra on here. Comes with ported matching elbow and quick change blower hub with 3 pulleys 2.4 2.5 2.6. Blower has less than 3500 miles but was just ported this past December and only has idle time on it since being gone through. 1900 plus...
Selling for a friend it's fully ported by Jay Blwn04SVTcobra on here. Comes with ported matching elbow and quick change blower hub with 3 pulleys 2.4 2.5 2.6. Blower has less than 3500 miles but was just ported this past December and only has idle time on it since being gone through. 1900 plus...
Basically stock 2010 other than 2.5 pulley, JLT 123mm intake, custom tune by Pete at Performance dyno in NH with DSS DS and NT05r 19in radials. Full weight car with completely stock suspension and exhaust. does this this ET sound right for this setup? Oh and gen2 MGW shifter which shifted...
Was on the phone with George from MGW and was about to order one of his shifters until he mentioned that they have a whole new design which replaces the center arm and eliminates that sloppy play once in gear. Has anyone else ordered one? He mentioned the end of the month should be ready for...
Selling for a friend, comes with everything in the picture. Has 28k for milage on all the parts. He's looking for a best offer right now plus the shipping cost.
Well it started as a very small grind In upper rpm back in January when I bought it but now I can't even bring it past 3k in 1st to 2nd without a long and very LOUD grind.. I literally have to drive it like an old lady going to 2nd which means somewhere around 2k. It also sometimes locks me out...
Was wondering weather to use the steeda one I have already but it requires to change the rear pinion flange. I would rather just get a complete bolt on one that utilizes the stock flange but don't know if it would be a weak point. The aluminum one piece shafts i see that uses the stock flange...
Got to take the gt500 to the dyno bone stock it put down 476hp 471tq with just over 10psi of boost. I got a k&n filter and ford racing resonator delete from a friend who upgraded to a jlt setup and changed it on the dyno just to see the gain and it netted 485hp 476tq. I seen the boost hit 11...
Looking to get a pulley and tune kit for now... car is all stock, just don't know if a new cai is needed like the JTL 127mm setup or is it overkill for what I'm doing. Also what's your favorite pulley size and company or kit to go with.
Just wondering if these intercooler pump system's has some type of thermostat built in? When I start the car I checked just to see if it was flowing and it wasn't' even with the motor up to temp... but when I take it for a spin and check it again while idling it's flowing fine?
Just want to...
I have a 2010 GT500 that I think has a shaker 500 because I don't have the sub in the trunk.. My question is would the nav be plug and play with the shaker 500 harness or would it be a different harness because of the A/C controls built into the nav.
So is it possible and worth it to add the...
I just ordered my certificate from shelby america and gt500 certificate from ford. I've tried searching for the production numbers and come up with it being just 2000 and it was limited for 2010? Is this correct and would anyone have a link to check what was produced in certain colors?
I'm not looking to do any exhaust work anytime soon and I actually like the exhaust note the way it comes from ford. I just want to know what some of you guys are making with the stock manifolds, cats and mufflers. I'll be just doing the basic tune, pulley, large inlet and heat exchanger for...
After reading on the site for the past few years and learning more about these gt500's I finally have my own. It's a 2010 with 8850 miles. I picked it up for 36k it was sitting at the dealer since last October and was originally listed for 40990. I'm pumped to say the least... it's bone stock...
Haven't seen it in person but looks clean and stock besides wheels and MBRP mufflers. He was asking 32000 but will take 30500. I'm not crazy about the wheels he said they are shelby rims. It has just over 11k for mileage. I've been looking for a while now and 30k is the most I can spend right...
Hi fellas I found a 2003 cobra 10th anniversary with 147000 on the clock, the seller wants 14500 for it and I'm not sure if that's the going rate on these now a days with that many miles on it. He's the second owner and has only had it since June of 2011. I pulled up the carfax and all is good...