Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Lightning Forums
2nd Generation
Check Engine light
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="JollyGiant" data-source="post: 10146051" data-attributes="member: 21077"><p>Don't know if this helps but...</p><p></p><p>Flash Electrically Eraseable Programmable Read Only Memory</p><p></p><p>Description </p><p>Flash Electrically Eraseable Programmable Read Only Memory (EEPROM) is contained in an Integrated Circuit (IC) internal to the Powertrain Control Module (PCM) . The EEPROM contains the vehicle strategy including calibration information specific to the vehicle and is capable of being reprogrammed or reflashed repeatedly.</p><p></p><p>As part of the calibration there is an area referred to as the Vehicle Identification (VID) block. The VID block must be programmed when replacing the PCM as described under Programming the VID Block for a Replacement PCM. Failure to perform this procedure may generate fault codes: P1635, P1639, VID Block not programmed or is corrupt. The VID block in an existing PCM can also be tailored to accommodate various hardware/parameter changes made to the vehicle since production. Failure to perform this procedure properly may generate fault code: P1635, Tire/Axle Ratio out of Acceptable Range is one of the main causes for code: P1639. This is described under Making Changes to the VID Block and also under Making Changes to the PCM Calibration. The VID block contains many items used by the strategy for a variety of functions. Some of these items include the VIN number, octane adjust, fuel octane, fuel type, vehicle speed limit, tire size, axle ratio, the presence of speed control and four wheel drive electronic shift on the fly versus manual shift on the fly. Only items applicable to vehicle hardware and supported by the VID block will be displayed on the scan tool.</p><p></p><p>When changing items in the VID block, the strategy will place range limits on certain items such as tire and axle ratio. The VID block is also limited to the number of times to be reconfigured. When this limit is reached, the scan tool will display a message indicating the need to flash the PCM again to reset the VID block.</p><p></p><p>Each of the procedures described below use the Worldwide Diagnostic System (WDS) . Reprogramming can be performed by a local Ford dealer for any non Ford facility. There are other Enhanced Scan Tools that may have reprogramming capabilities available. Refer to the manufacturers users manual for details.</p><p></p><p>Programming the VID Block for a Replacement PCM </p><p>A new PCM will contain the latest strategy and calibration level for a particular vehicle. However, the VID block will be blank and will need programming. There are two procedures available. The first is an automatic data transfer from the old PCM to the new PCM and the second is manual data entry into the new PCM.</p><p></p><p>Automatic data transfer will be performed if the old PCM is capable of communicating. This is done by the use of a scan tool to retrieve data from the old PCM before removing it from the vehicle. The stored data can now be downloaded to the new PCM after it has been replaced.</p><p></p><p>Manual data entry must be performed if the old module is damaged and/or incapable of communicating. Remove and replace the old PCM. Using a compatible Scan Tool select and execute Module/Parameter reprogramming referring to the manufacturers users manual. Important, make certain that all parameters are included. Failure to properly program Tire Size in revolutions per mile, (rev/mile = 63,360 divided by the tire circumference in inches) Axle Ratio, 4x4/4x2, and/or Manual/Electronic shift on the fly (MSOF/ESOF) may result in codes: P1635, P1639. You may be instructed to contact the "AS BUILT" data center for the information needed to manually update the VID block with the scan tool. Contact the center ONLY if the old PCM cannot be used or the data is corrupt. For Ford L-M technician's, contact your National Hotline or the Professional Technician Society (PTS) web sight for "AS Built" data. Non Ford technicians, use the Fed World website at "fedworld.gov". Select Auto Service Information and search for "Calibrations" or "Vehicle Calibrations" then specify vehicle manufacturer, model name and model year as required.</p><p></p><p>Making Changes to the VID Block </p><p>A PCM which is programmed may require changes to be made to certain VID information to accomodate vehicle hardware. Refer to PCM/Module Reprogramming on the Scan Tool.</p><p></p><p>Making Changes to the PCM Calibration </p><p>At certain times, the entire EEPROM will need to be completely reprogrammed. This is due to changes made to the strategy or calibration after production or the need to reset the VID block because it has reached its limit. Refer to PCM/Module Reprogramming on the Scan Tool.</p></blockquote><p></p>
[QUOTE="JollyGiant, post: 10146051, member: 21077"] Don't know if this helps but... Flash Electrically Eraseable Programmable Read Only Memory Description Flash Electrically Eraseable Programmable Read Only Memory (EEPROM) is contained in an Integrated Circuit (IC) internal to the Powertrain Control Module (PCM) . The EEPROM contains the vehicle strategy including calibration information specific to the vehicle and is capable of being reprogrammed or reflashed repeatedly. As part of the calibration there is an area referred to as the Vehicle Identification (VID) block. The VID block must be programmed when replacing the PCM as described under Programming the VID Block for a Replacement PCM. Failure to perform this procedure may generate fault codes: P1635, P1639, VID Block not programmed or is corrupt. The VID block in an existing PCM can also be tailored to accommodate various hardware/parameter changes made to the vehicle since production. Failure to perform this procedure properly may generate fault code: P1635, Tire/Axle Ratio out of Acceptable Range is one of the main causes for code: P1639. This is described under Making Changes to the VID Block and also under Making Changes to the PCM Calibration. The VID block contains many items used by the strategy for a variety of functions. Some of these items include the VIN number, octane adjust, fuel octane, fuel type, vehicle speed limit, tire size, axle ratio, the presence of speed control and four wheel drive electronic shift on the fly versus manual shift on the fly. Only items applicable to vehicle hardware and supported by the VID block will be displayed on the scan tool. When changing items in the VID block, the strategy will place range limits on certain items such as tire and axle ratio. The VID block is also limited to the number of times to be reconfigured. When this limit is reached, the scan tool will display a message indicating the need to flash the PCM again to reset the VID block. Each of the procedures described below use the Worldwide Diagnostic System (WDS) . Reprogramming can be performed by a local Ford dealer for any non Ford facility. There are other Enhanced Scan Tools that may have reprogramming capabilities available. Refer to the manufacturers users manual for details. Programming the VID Block for a Replacement PCM A new PCM will contain the latest strategy and calibration level for a particular vehicle. However, the VID block will be blank and will need programming. There are two procedures available. The first is an automatic data transfer from the old PCM to the new PCM and the second is manual data entry into the new PCM. Automatic data transfer will be performed if the old PCM is capable of communicating. This is done by the use of a scan tool to retrieve data from the old PCM before removing it from the vehicle. The stored data can now be downloaded to the new PCM after it has been replaced. Manual data entry must be performed if the old module is damaged and/or incapable of communicating. Remove and replace the old PCM. Using a compatible Scan Tool select and execute Module/Parameter reprogramming referring to the manufacturers users manual. Important, make certain that all parameters are included. Failure to properly program Tire Size in revolutions per mile, (rev/mile = 63,360 divided by the tire circumference in inches) Axle Ratio, 4x4/4x2, and/or Manual/Electronic shift on the fly (MSOF/ESOF) may result in codes: P1635, P1639. You may be instructed to contact the "AS BUILT" data center for the information needed to manually update the VID block with the scan tool. Contact the center ONLY if the old PCM cannot be used or the data is corrupt. For Ford L-M technician's, contact your National Hotline or the Professional Technician Society (PTS) web sight for "AS Built" data. Non Ford technicians, use the Fed World website at "fedworld.gov". Select Auto Service Information and search for "Calibrations" or "Vehicle Calibrations" then specify vehicle manufacturer, model name and model year as required. Making Changes to the VID Block A PCM which is programmed may require changes to be made to certain VID information to accomodate vehicle hardware. Refer to PCM/Module Reprogramming on the Scan Tool. Making Changes to the PCM Calibration At certain times, the entire EEPROM will need to be completely reprogrammed. This is due to changes made to the strategy or calibration after production or the need to reset the VID block because it has reached its limit. Refer to PCM/Module Reprogramming on the Scan Tool. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Lightning Forums
2nd Generation
Check Engine light
Top