Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Cobra Forums
The Terminator
How-To
How to Polish Aluminum & S/S to a mirror finish.
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="SmokinCobra420" data-source="post: 6671413" data-attributes="member: 51601"><p>Tools required.</p><p>*Sand Paper</p><p>>Grit 400-500-600-800-1000-1200-1500-2000</p><p>*spray bottle</p><p>*Scotch brite pads</p><p>*Micro fiber finishing cloth</p><p>*Your choice of metal polish or cleaner ( I like 3M Aluminum & Stainless polish)</p><p>*High speed buffer and thick fiber buffing pad</p><p>*Some sort of cleaner, like a degreaser if the metal is filthy, mine was only mildly dirty, i used some dish soap.</p><p></p><p></p><p>1) fill spray bottle with a mild soap/water mix, prep the surface using the soapy water in the spray bottle and scotch brite pad to remove any dirt and grime.</p><p></p><p>2)strat with the 400 grit sand paper and begin working the surface in a back and forth motion, never use a circular motion, it will cause swirling rather then flowing in the same direction. Continue this process working the whole surface over, and wroking up from 400 to 500 to 600 ect. you may also want to wet the surface often to aid in sanding.</p><p></p><p>3)Once you have brought the surface to a fine shine after the 2000 grit, now you will bring in the buffer. Apply a small amount of polish to the top face of the buffer pad. Start by slowly spinning the buffer to apply the polish. Gradually increase buffer speed to full power, and begin working in back and forth motions across the surface, applying a good amount pressure to increase friction, and work the surfae until there is no more residue remaining. </p><p></p><p>4) Finally go back over everything with a thin layer of polish and a buff it with the micro fiber cloth to get that extra little *Bling*!</p><p></p><p></p><p>It will be easier after you get the feel for the buffer. It took me about 30 mins to get a good feel for how the buffer would move across the different angles, just be sure to not let the center screw or bolt holding the pad on the buffer touch anything, it will scratch. </p><p></p><p>Hope this helps anyone looking to bring a great mirror finish to any of there aluminum or S/S parts for our cars. </p><p></p><p>I did my driveshaft and bassani cat backs.</p><p></p><p><a href="http://www.svtperformance.com/forums/showthread.php?t=492145" target="_blank">http://www.svtperformance.com/forums/showthread.php?t=492145</a></p></blockquote><p></p>
[QUOTE="SmokinCobra420, post: 6671413, member: 51601"] Tools required. *Sand Paper >Grit 400-500-600-800-1000-1200-1500-2000 *spray bottle *Scotch brite pads *Micro fiber finishing cloth *Your choice of metal polish or cleaner ( I like 3M Aluminum & Stainless polish) *High speed buffer and thick fiber buffing pad *Some sort of cleaner, like a degreaser if the metal is filthy, mine was only mildly dirty, i used some dish soap. 1) fill spray bottle with a mild soap/water mix, prep the surface using the soapy water in the spray bottle and scotch brite pad to remove any dirt and grime. 2)strat with the 400 grit sand paper and begin working the surface in a back and forth motion, never use a circular motion, it will cause swirling rather then flowing in the same direction. Continue this process working the whole surface over, and wroking up from 400 to 500 to 600 ect. you may also want to wet the surface often to aid in sanding. 3)Once you have brought the surface to a fine shine after the 2000 grit, now you will bring in the buffer. Apply a small amount of polish to the top face of the buffer pad. Start by slowly spinning the buffer to apply the polish. Gradually increase buffer speed to full power, and begin working in back and forth motions across the surface, applying a good amount pressure to increase friction, and work the surfae until there is no more residue remaining. 4) Finally go back over everything with a thin layer of polish and a buff it with the micro fiber cloth to get that extra little *Bling*! It will be easier after you get the feel for the buffer. It took me about 30 mins to get a good feel for how the buffer would move across the different angles, just be sure to not let the center screw or bolt holding the pad on the buffer touch anything, it will scratch. Hope this helps anyone looking to bring a great mirror finish to any of there aluminum or S/S parts for our cars. I did my driveshaft and bassani cat backs. [url]http://www.svtperformance.com/forums/showthread.php?t=492145[/url] [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Cobra Forums
The Terminator
How-To
How to Polish Aluminum & S/S to a mirror finish.
Top