Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Cobra Forums
SVT Shelby GT500
KB to VMP the results
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="FEARSNO1" data-source="post: 15194336" data-attributes="member: 9770"><p>i don't agree with anything you did here, and I'm not being an ass, but the 2.8 KB will fit under a stock hood with no lowering at all, a small 3"x8" hole is needed in the ribs of the hood and that's it! not sure why this wasn't already known to you, mine was that way for 7 years till i swapped to the 4.0, and i had long tubes, and my car is slammed 2.2" in the front. as for the blower swap, that boggles my mind to, the KB doesn't make as much tq as the TVS because as we all know the higher you spin any PD blower the higher the tq and the TVS spins much faster at 18 psi than the KB does, if you were to run the KB higher into it's efficiency range the tq comes way up, the TVS is a nice blower especially for cost but you already had a KB. The KB also has so much more potential than the TVS. and the also the TVS is gonna run way hotter than the KB will at the same boost level</p><p></p><p>i included a dyno i did to compare pulleys, my car was basically close to your mods, KB stage III kit, headers and full exhaust. 18psi vs 23 psi (2.5" pulley vs 3.0" stock lower) same day same dyno!</p><p>+113 FT/LBS</p><p></p><p>[ATTACH]60377[/ATTACH]</p></blockquote><p></p>
[QUOTE="FEARSNO1, post: 15194336, member: 9770"] i don't agree with anything you did here, and I'm not being an ass, but the 2.8 KB will fit under a stock hood with no lowering at all, a small 3"x8" hole is needed in the ribs of the hood and that's it! not sure why this wasn't already known to you, mine was that way for 7 years till i swapped to the 4.0, and i had long tubes, and my car is slammed 2.2" in the front. as for the blower swap, that boggles my mind to, the KB doesn't make as much tq as the TVS because as we all know the higher you spin any PD blower the higher the tq and the TVS spins much faster at 18 psi than the KB does, if you were to run the KB higher into it's efficiency range the tq comes way up, the TVS is a nice blower especially for cost but you already had a KB. The KB also has so much more potential than the TVS. and the also the TVS is gonna run way hotter than the KB will at the same boost level i included a dyno i did to compare pulleys, my car was basically close to your mods, KB stage III kit, headers and full exhaust. 18psi vs 23 psi (2.5" pulley vs 3.0" stock lower) same day same dyno! +113 FT/LBS [ATTACH]60377.vB[/ATTACH] [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Cobra Forums
SVT Shelby GT500
KB to VMP the results
Top