Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Cobra Forums
New Edge Cobras
Top tranny bolts?!?!?!?!
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="3B99SVT" data-source="post: 7895161" data-attributes="member: 35689"><p>Well, thanks to your input the tranny is out. That stupid front O2 sensor bracket was a pain though. After the tranny slid back about a 1/4" it trapped the bracket between the bellhousing and the tunnel. I think I need to do some touch-up paint now. It would have helped if my hands were smaller (which reminds me -- time to replace my fuel filter too).</p><p></p><p>I tried one of those pilot bearing pullers and it didn't even budge it. Just over two pieces of bread did the trick. </p><p></p><p>So now all the old pieces are out. I had to run to Ford to get a new pivot bolt & clutch fork since there was significant wear on them + one of the spring holders on the clutch fork was busted off. All the new stuff: Fidenza Al flywheel (finally got here!), 03/04 clutch & PP, Ford throw-out bearing, pilot bearing, clutch fork & pivot ball. I've got a little grease thrown on the tunnel right where the front u-joint is so I'll probably change that too.</p><p></p><p>Car's been down over a month. While I was waiting for the flywheel to arrive I put my 03/04 front diff brace w/MM poly mounts. I have the rear MM mount too, but I think I'll wait until I get more $ to get some of Bruce's stuff for the IRS and do it all at the same time. I'll be rolling soon!!! Thanks guys!!!! I would have been banging my head against the wall and probably broke something if I didn't get your help.</p></blockquote><p></p>
[QUOTE="3B99SVT, post: 7895161, member: 35689"] Well, thanks to your input the tranny is out. That stupid front O2 sensor bracket was a pain though. After the tranny slid back about a 1/4" it trapped the bracket between the bellhousing and the tunnel. I think I need to do some touch-up paint now. It would have helped if my hands were smaller (which reminds me -- time to replace my fuel filter too). I tried one of those pilot bearing pullers and it didn't even budge it. Just over two pieces of bread did the trick. So now all the old pieces are out. I had to run to Ford to get a new pivot bolt & clutch fork since there was significant wear on them + one of the spring holders on the clutch fork was busted off. All the new stuff: Fidenza Al flywheel (finally got here!), 03/04 clutch & PP, Ford throw-out bearing, pilot bearing, clutch fork & pivot ball. I've got a little grease thrown on the tunnel right where the front u-joint is so I'll probably change that too. Car's been down over a month. While I was waiting for the flywheel to arrive I put my 03/04 front diff brace w/MM poly mounts. I have the rear MM mount too, but I think I'll wait until I get more $ to get some of Bruce's stuff for the IRS and do it all at the same time. I'll be rolling soon!!! Thanks guys!!!! I would have been banging my head against the wall and probably broke something if I didn't get your help. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Cobra Forums
New Edge Cobras
Top tranny bolts?!?!?!?!
Top