Currently running 12-150 but my spring is adjusted all the way up to get my ride height to 26 inches at the fender lip I’m thinking a 12-200 might be better? Or a 12-175? I know I can go to a 14 inch spring but I heard of spring bending and binding with that. Also they sell spring spacers that...
Hey guys I wanted some advice I have Lakewood 90/10 struts up front and Lakewood 50/50 in the rear however I have a blown driver rear shock and I’m undecided to go with the same Lakewood 50/50 or strange 10 way single adjustable I’m on a 15x10 and 275/60 or 295/55 15 rear Hoosier drag radial and...
How would I go about adjusting the cruise control clutch switch it’s too sensitive and as soon as you touch the pedal it activates I’m using a N2MB wot box and I need it to activate about 2 inches of pedal travel being depressed right now it activates barely touching the clutch I know there was...
I do t know why I haven’t jumped on this filter quicker this thing flows like a mother fer my car isn’t a daily so this zero restriction filter is perfect I’ve been using a cotton filter for 20 years and just discovered this! I picked up 1psi boost over the cotton type
Sent from my iPhone...
Anyone have experience with these it claims 2-3 number octane one bottle per tank at this lower concentration does it still turn plugs orange? I had a bad experience with Torco accelerator in the past even just doing 91 pump to make it 95-96 octane just wanted to see if the smaller boostane...
Guys my n2mb wot box blue led lights up momentarily when I turn the key on but while car is running the led no longer stays smile it’s completely off if I push the little black button no lights come on but it does shut the unit off as I tried pressing in clutch and full throttle it didn’t allow...
Has anyone experienced a blown leaking lakewood shock it only has maybe 140 miles and the rear driver is blown out and leaking oil sucks because it’s past the 90 day warranty but they should not do this
Sent from my iPhone using the svtperformance.com mobile app
Just wondering if anyone in the terminator community still does this I run without my passenger headlight on my 97 I datalogged some iat1 and 2 temps and I was surprised how effective this was temps were 20 degrees cooler they were precisely ambient vs with the headlight in place I seen 20...
Do they still make them? I have one on my 97 o love the fact they are all aluminum and was a direct drop in replacement also 1.5 inches thick vs 1 inch in the 97-98 cobra. I’d like to get another one as a spare because I have heard nothing but trouble trying to fit thicker radiators like SVE...
Guys I know I read it on here before where a member said he was able to remove the alternator without removing the blower or the coolant crossover tube does anyone know if this is true? I’ve done it before by removing the blower and once by removing just the crossover. It looks like if you...
This is a how to mod to run your high speed fan on demand wether at the track cooling between runs or even slow moving traffic. It gives you the option to manually control.
Disconnect the ground from you battery
Dissemble your shifter housing bezel and arm rest glove box
Next remove the...
I removed that cowl to hood weather strip a few years back because it was torn with the hood closed you can see into the engine bay just a bit maybe 1/2 inch or so by having g that open does it let hot air out or does it force air from the windshield into the engine bay? I’m thinking about...
After living outside under a carport since 2005 I now keep my cobra inside in a climate controlled insulated garage where she will live out the rest of her life
Sent from my iPhone using the svtperformance.com mobile app
Nothing under 500hp guys let’s see the baddest 4V’s SVTP has to offer and what they belong to. Make, model, year, mods and power level!
1997 Cobra
Fully built original forged teksid block,9.2 comp cp forged pistons, modmax forged h beams, 1 7/8 long tubes, ported and polished b heads, 1.5l...
Does anyone have any experience with a small dry shot of nitrous pre rotors on a twin screw or Eaton? I’m thinking of putting a dyno tune dry kit 35-50 shot pre blower to help cool the charge and make a little power as well. I heard a small 35-50 shot will actually make more due to the cooling...
Hey guys I know of the high speed cooling mod where you tap into pin 46 light green purple stripe on the ecm harness passenger kick panel and run it to a ground. However is there another way to do this under hood? I removed all my A/c system and the harness to the high pressure ac switch is just...
Hey guys I’m in the process of up grading my ignition system and I wanted to see how my 27 year old packs are doing so my primary resistance is 1.2-1.3 ohms left and right pack my secondary are at 12.6-12.75k ohm left and right
Testing specs call for
Primary resistance 0.3 - 1.0 ohms...
What is a good way of cleaning out the spark plug wells on our cars? I sprayed them with brake cleaner and blew out with compressed air then removed the plugs(changing plugs out) is there a good way of scrubbing them out?
Sent from my iPhone using the svtperformance.com mobile app
What are these gray connectors that hook to the coil packs? Do they have a purpose or can they be left unplugged just wondering because I’m about to put my new plug wires and coil packs on the car
Sent from my iPhone using the svtperformance.com mobile app
So I placed a special order 12/1 and barely received them yesterday they claim 40 ohm per foot and according to my multimeter they are spot on!!!!! These blow the ford racing wires out of the water frpp wires are 1000 ohm per foot in terms of resistance. They are made in China but who cares the...
Does anyone make a 3.5 inch rear wheel stud for 94-98 rear axles? I know Moroso makes 3 inch but I’m needing 3.5 inch in case I need to use my 1/2 inch spacers with my weld draglites to make the shank lugs NHRA legal length on the studs
Sent from my iPhone using the svtperformance.com mobile app