Timspony how you put a 100mm idler pulley on a 3.0. My rub the each other and couldn't use it
VMP TVS 2.3 Belt sizes
- Thread starter Senkak
- Start date
My 100mm auxiliary doesn't rub on a 3.2, and I have a metco same as timspony. Could it be the brand of auxiliary?
Not sure if this works with a vmp....but if it does, it sure takes the guess work out. You can run the same belt for multiple pulley combos, like a pump gas and race gas (e85) tune
Not an issue at all!!! .... Must be the manufacture??!!
As stated ^^^ we're running Metco Aux. equipment :rockon:
Yea guess I need to go with metro. Think I got billet flow
Whoops. That would probably be a good idea. Doh!
Belt size: K080806
Upper pulley size: 3.0"
Lower pulley size: 4lb
Size and quantity of idlers: 3-100mm
Auxiliary idler pulley size and which manufacturer:Billetflow 100mm
Alternator pulley size: 3.2"
Belt size: K080810
Upper pulley size: 3.2"
Lower pulley size: 4lb
Size and quantity of idlers: 3-100
Auxiliary idler pulley size and which manufacturer: Billetflow 90mm
Alternator pulley size: 3.2"
2.6'' upper pulley
Gates 74.5'' belt
Stock lower pulley
100mm aux idler
2 100mm idlers
1 90mm idler
Gates 74.5'' belt
Stock lower pulley
100mm aux idler
2 100mm idlers
1 90mm idler
Anybody know what belt size I will need I have a 2.8 pulley and everything else is stock
Where are the TVS owners....
Thanks Corey!
Belt size: 75" Gatorback (4080750) Stock size belt
Upper pulley size: 2.8
Lower pulley size: Stock
Size and quantity of idlers: 2 100mm & 1 92mm (Billetflow)
Auxiliary idler pulley size and which manufacturer: 100mm Billetflow
Alternator pulley size: Stock
Upper pulley size: 2.8
Lower pulley size: Stock
Size and quantity of idlers: 2 100mm & 1 92mm (Billetflow)
Auxiliary idler pulley size and which manufacturer: 100mm Billetflow
Alternator pulley size: Stock
Thanks Danny!
Think you need a 74". The only way i can get my belt on is to put the snub idler on after the belt is on the pulley. Also, you may want to remove the tensionor stop inorder to accommodate a smaller belt
Rather than trying to do all the different belt combinations for every single setup. I recommend you just list the different belt sizes needed with stock idlers, and lower. Then from there point people to metco chart to determine what they need to do from there. That's what I did with my Whipple, worked perfectly.
Did you figure out which belt you needed? I will have a similar set-up just with a 3.0 upper/2.6 upper for race gas.
I use a Gates HD Green belt with the 2.8 upper, stock lower, 100 metco aux idler and vmp stock size idlers. When I put the 2.6 on the 74 belt was very easy to put on. That is why I thought I may need a shorter belt. Gates no longer makes a 73.5 belt in the HD series. I was just testing on the car on the 2.6 pulley with Torco. With the cold weather here lately, I was hitting 21 psi. So after that I jumped out of it and put the 2.8 pulley back on there for the time being. I may get a few 100mm idlers to replace the stock size 90mm idlers, so when I run the 2.6 upper again the 74in belt will be a bit tighter.
Belt size: K080785HD
Upper pulley size: 3.0"
Lower pulley size: Metco 4#
Size and quantity of idlers: Stock
Auxiliary idler pulley size and which manufacturer: Steeda 100 mm
Alternator pulley size: Metco 3.2"
Upper pulley size: 3.0"
Lower pulley size: Metco 4#
Size and quantity of idlers: Stock
Auxiliary idler pulley size and which manufacturer: Steeda 100 mm
Alternator pulley size: Metco 3.2"
Users who are viewing this thread
