Official eaton swap thread, parts and links.

[crazycarlo]

Please sticky this somewhere. These are all the links I have collected over the years. Most of the stuff u will need to do the swap is in here. Also i have included a parts list with the part number. This list is not including the heads and related parts if u have a 96-98 cobra and need to swap.

https://docs.google.com/View?id=dgcxhnzw_42gm5gwmdv

Mark Olson's Mustang Cobra

Questions about putting an Stock Eaton on a 96-98 Cobra??

[ame=http://www.mercurymarauder.net/forums/showthread.php?t=60366]Eaton Swap Parts List Thread - MercuryMarauder.net Forums[/ame]

2r3z6312baa - Crank pulley /Harmonic Balancer
f1az6378a - washer for balancer
f5rz6a340b - bolt for balancer
2r3z6312ba - Supercharger Crank drive pulley
2r3z10153ca - Bracket that replaces stk. alt. on 99-01 Cobra’s and 03/04 Mach 1’s (Comes w/ pulley below if bought used)
yw7z8678aa - pulley for above bracket
2r3z6b209bc - Pulley bridge assembly for S.C. (If bought new it comes with the bridge, 2 idlers and tensioner)
(8678B) Idler pulley,timing cover pass. side
yw7z8678aa - pulley on drivers side of timing cover
(6D080) Timing cover (if bought new, it comes w/ pulley on drivers side and tensioner)
s5az6700a - timing cover seal
(10A313) Upper alternator bracket
(10153) Lower alternator bracket
(10346) Alternator
1U2Z-14S411-TA Electrical connector (alt. to harmness )
(6B209A) Tensioner on timing cover
2r3z8260ab - Radiator hose
2r3z8a593ab - Radiator hose
2r3z8k576aa - Radiator hose
2r3z8548aa - Water cross over pipe
(6881) Cobra oil cooler adapter
(6A642) Cobra Oil cooler
2r3z9002aa - Cobra fuel tank (optional)
2r3z9h307ab - Cobra fuel pump (optional)
2r3z6f066aa - Eaton supercharger
2r3z9424bb - Lower intake
(6K775) Garrett factory intercooler
3U2Z-14S411-SSA IAT2 sensor connector
2r3z9n491ca - Intercooler hard lines that hug the block (If bought new, it comes w/ part # 9l443c)
(9N491A) Intercooler hard lines that come from the h/e
3r3z9l443aa - Intercooler line that goes from the i/c adapter to i/c res.
2r3z9l443ba - Intercooler line that goes from the i/c adapter to the hard lines that hug the block
2r3z9l443ca - Intercooler line that goes from the hard line against the block to i/c pump(included w/ the hard line that hugs the block if purchased new)
2r3z9l443da - Intercooler line that goes from hard line to hard line
2r3z9l443ea - Intercooler line that goes from hard line from h/e to i/c pump
2r3z9l443fa - Intercooler line that goes from hard line and connects to h/e
2r3z9l443ga - Intercooler line that goes from hard line and connects to h/e
f8yz8501aa - Ford / Bosche water pump for intercooler
2r3z8n500ac - Intercooler pump bracket
2r3z8k226aa - Factory heat exchanger
2r3z8a193aa - Heat exchanger mounting bracket
2r3z8c386aa - 2each bracket clamps for h/e
(9N491B) Lower manifold to intercooler water adapter
2r3z9a589ca - Plenum
(9B659) Intake tube from maf to t/b.
(9F715) IAC valve
2r3z9f593ba - Injectors
(6F089) Boost bypass actuator
2r3z9a825aa - Cruise control cable
2r3z9a758aa - Throttle cable
(9728) Throttle and cruise control cable mounting bracket
1l3z12b579aa - MAF
xw4z9d475ab - EGR valve
2r3z9d477ad - EGR tube
(6C324) PCV tubing
(9F479) Sensor on the back of the S/C
(9J432) Bracket for vacuum stuff on left side of the S/C
(9H465) Vacuum stuff
(9J459) Vacuum stuff
(9J460) Vacuum stuff
(9E498) Hose's or tube cluster of connectors for the vacuum parts above
e83z9f670a IAC gasket
2r3z6020aa - Timing cover gasket LH side
2r3z6020ba -Timing cover gasket middle
2r3z6020ca - Timing cover gasket RH side
2r3z9h486aa - Lower intake to S.C. gasket
2r3z9l437bb - Plenum to S/C gasket
e6az9d476b - EGR gasket
2r3z3490aa - Power steering resevoir bracket.
I/C resivoir tank
i/c pigtail
S/C 8 rib belt
inner acc. belt.
n804178s309 - (8) Nuts for plenum, coolant crossover and pulley bridge can be picked up at local auto parts store in help section.
n805164437 - (1) Bolt for pulley cage to timing cover.
n808102s437 - bolt that is used on the idlers and pulleys. Only need if you buy parts seperately. You will need a total of at least 6 of these.
n808920s437 - Pulley bridge bolts
n606677-s36 (4) Bolts to bolt the bracket clamps to the h/e bracket
N605909s437 - (4) bolts for the upper alt. bracket
n807274s437 (1) lower alt. bracket to alt bolt
n811313s431 (4) studs to bolt plenum to s/c
w506404s437 (10) i/c to s/c bolts

 

[STAMPEDE3]

Remember guys who look, as he said you must do the C head swap first so add that to the cost.

 

[SVTContique]

In the end its easier to put on a P1SC or similar centri.

 

[maniak87]

In the end its easier to put on a P1SC or similar centri.

true, but both have different feel/powerbands though.

 

[crazycarlo]

In the end its easier to put on a P1SC or similar centri.

Its easier and cheaper but I made this thread to help out those who would like to spend the money to do the swap.

 

[jmc302]

I'm doing an Eaton swap onto my 01 GT (Tork Tech Kit), and I have two questions from the parts list above. If you could help it would be greatly appreciated.

1. What is the part number for the IC Pump pigtail, or where can I find it?

2. What is "(9F479) Sensor on the back of the S/C"? I see the spot for it on my Eaton, but just planned on blocking it off if I did not use it...just want to make sure it isn't a vital function.

My swap is going good, and I am coming down the the final small parts to get it completed. Thanks for your help!

 

[PACIFICGREENSVT]

Intercooler pump wiring pigtail Part number 3U2Z14S411BJA / WPT260

drill and tap the hole in the back of the lower intake and use a Lightning threaded AIT.
Then extend the wires.

 

[jmc302]

Thanks!

The lower intake that came with the kit already has a threaded port for a Lightning IAT between cylinders 2 and 3, so I will just go ahead and seal up the spot on the drivers side of the blower.

 

[PACIFICGREENSVT]

Do you have a pic? I would like to see where they put it^

 

[jmc302]

I do have a picture, but I need to get something uploaded to the site so I can link to it.

 

[jmc302]

Here is the pic. The IAT port is the threaded hole on the #2 port.

http://s1187.photobucket.com/albums/z389/jmc302/?action=view&current=P1010024.jpg

 

[PACIFICGREENSVT]

Thanks:thumbsup:

 

[Mustang Matt]

Why don't we make this a sticky?

Paging: 97CasperCobra and/or STAMPEDE3

 

[PACIFICGREENSVT]

Thought I would add, I wound up putting the IAT sensor in the front of the lower intake.

 

[crazycarlo]

Nice I'm planning on just splicing my air wires into the iat 2 sensor that's already on the back of the blower.

 

[STAMPEDE3]

Why don't we make this a sticky?

Paging: 97CasperCobra and/or STAMPEDE3

It is in the FAQ/Mods/Track tip sticky.

Has been for a year.