How did ya'll close the holes up? jb weld, welding them? apparently the welder for the shop it's at "doesn't have time" or some other dumb excuse so now i either have to find a place to weld them, which i have no idea of anyone, or i've seen that people have used jb weld but i'm iffy on that...
Replaced IAC/TPS the past couple of days.
Car doesn't search for idle as badly anymore, however it does hang around 2k and drop after i come to a stop for a few seconds. Sometimes it drops to 1600ish other times it will drop to 1k. When rolling in nuetral above 15 or so it will fluctuate...
Recently both have stopped working at teh same time. I don't have my owners manual and i can't seem to figure out which fuse it might be.
Someone mind helping me out here and let me in on which one im looking for? lol
i've searched on here adn on google and can't seen to find the info i'm looking for regarding my a/c issue.
Yesterday I went on some errands for my girlfriend and noticed my a/c isn't blowing cold. i bought a recharge kit thinking that was the issue, but when i got home i let it idle for a...
My amps are blown, and currently im listening to my phone in the door pocket to increase sound volume lol.
at this point after what i've read, i've just gonna have a buddy of mine help me and redo the whole car and pull the old 460 stuff out.
Can someone point me in a direction wher ei can...
Rebuilt my rearend at the end of last year because ti was super loud. Turned out that the drive side axle had some spots on it that where causing it to make noise, so it's still loud and getting louder.
Don't really have the money for new forged ones at the moment, anyone have any suggestions...
Got an axle causing some annoying noise so i'm looking to replace it with one in better condition. the Shop said there was some issue with the surface of the axle causing it to be ungodly loud.
(everything else was replaced back in september)
wanted to give it a shot posting in here to see...
The other night my cd player (aftermarket kenwood) stopped working.
Pulled it out of the dash and a wire had came uncovered. It was a 12 volt acc on wire i believe. A blue wire. Taped it back up to kill the ground and the cd player works and plays cds.
Now there is zero sound, not even a...
All new Maximum Motorsports setup installed. The MM valved bilstiens matched springs LCA, stock uppers with new bushings.
This happens when i park in my girlfriends driveway.
Driver side
Pass. side
The driveway in cut pretty awkward i guess it dips down right past the gravel line.
The...
Like the title says i'm looking for some rear tires for my 97. Leaning towards the nitto 555's in 275. right under 150 a tire on average and i have them on the front already in a 245.
But before i bite the bullet and order them, i wanted to post in here and see if there's something better...
Okay, so last wednesday i finally picked my car back up from a rear end freshen up.
New seals/bearings/frpp diff cover/CF friction plates and 4.10s. (MM LCA's and stock uppers).
I've noticed it's still making noise, and the shop mentioned they had a hard time adjusting the backlash due to...
Like title says, i'm putting 4.10s in the car while it's in getting the rear end redone.
How do i correct the inaccuracy of the speedo? I'm going from 3.73s from a previous owner, and i'm unsure of how he went about correcting the difference when he installed.
What are my options?
So being on a budget throws the maximum motorsports setup out the window.
The uppers HAVE to be replaced. They're some adjustable something that was on the car when i bought it, no idea of brand. All i know is they're shot.
Lowers need the bushings replaced but by the time i pay for bushings...
Have a set of about 20k mile Eibach sportlines i just pulled off my 97.
just switched to maximum motorsports springs etc so they're just sitting around. no issues aside from the paint stuff below.
Looking to get 90 for them, shipped.
Eibach Sportline Spring Kit (79-04 V8 Coupe; 99-04 V6...
Like the title says, next week i'm dropping it off to get it redone.
First, what power levels are the 28 splines good for, and what level do i need to look into a 31 spline setup?
I plan on bumping up to 4.10s (from 3.73s) doing a frpp diff cover and...
my next question is, carbon fiber...