Search results

Im looking into a AEM failsafe wideband gauge cuz i think it sounds like a good lifeline if something cracks with the fuelsupply. My question is: You driving with a gauge like this? Is it enough to only have one 02 sensor(?), the AEM only supports one 02 sensor... What gauges are there on the...

Im starting to save money for a upgradekit for my 2.8L KB to a 4.2L KB. Is it safe do do about 1000hp on my new built engine? What horsepower do you guys think the engine can handle? This is the setup: Afco Duelpass heat exchanger 105lbs injectors Ford racing performance intercooler High...

Looking for some upgrade, i have the 2.8L KB S/C on my mustang today. Kennebell have upgrade kits for just that 2.8L to 4.2-4.7LC thats sounds very intresting for me. Somebody that done that upgrade already that can tell me the difference?

Me in the red mustang , burnouts and fun on the streets in SWEDEN. BMW are very popular to TURBO in sweden. 500+hp in every one. Red one in video 1000RWHP+ and also the same for the Silver E30 in car that weight half what the mustang do :lol: ENYOY looking at the car culture in sweden...

What to do? Happend before for anybody else? What to do to fix it? New threads or just get a set of new heads?

8:3.1 is that to low compression in my engine? I have a built engine with -17cc pistons... Driving a kennebell 2.8 19psi making 740hp at the engine like 620rwhp? What compression is better and safe to drive with the kennebell, 9.4 , 10.4 or something like that? 0.20 over or stock bore or...

When i pull/push the wheel from the car its like there are some kind of distance inside the rear axle is this normal? Turn up your speakers! :rockon: http://youtu.be/GYKKY4kd8Mg?list=UUq6itkqA3nzULIJ1X1xqzmA

Fits good, but the "hoses" get bent real easy need to take out the curves. For the driver side can i needed to drill a hole so i could mount it, its a tight fit ! I was out for a test today driving for 1-2 hour, after that i opened the passengerside can and some OZ of oil came out, i tried the...

Driving with oem driveshaft for some time now with 700hp+ but one weekend the luck run out. Was lining up for some burnout (in water) on the street in Sweden. Reved up 4-5k released the clutch and....PAboom Scramble Scramble gearshifter was moving all around. I was thinking WTF!?, hope its not...

Me doing a little burnout in 1st and 2nd gear, just flooring it in second gear no brakes...https://www.youtube.com/watch?v=KHRDlQ_o7OI

A little highwaymovie with poor videoquality, me racing a Ninja"turtle" https://www.youtube.com/watch?v=vV6nqtYktG8

E85 Conversion, best "fuelpackage"? HP gain? E85 gt500 users tell me :pop:

I have a Shelby gt500 2008, with built engine (cams,pistons and rods) Im driving on pumpgas 98 (like your 93) and the 2.8L blower makes 20-22psi and the dyno "only" shows 740hp in 4-gear with the OEM pumps "boost a pump" is doing 100%. 8:3.1 in comp But is 20-22psi to mutch on pumpgas? (98)

I have these on my kennebell mustang and now im getting a new tune but dont know what this is... The guy that built this engine says its Bosch 105lb injectors. The numbers are this: 044519 5-05-05-12 PA6 and 060 those are the numbers i found on the injector. These numbers i see with the...

Hello. I have a Shelby -08 with some mods, and a problem... When im out driving the pony i get the "bip" and failsafe engine mode is activated... cant rev above 4000rpm. I put my SCT in to read the codes and it says: P1227-Wastegate failed closed P0153-CKT slow response P2198-02...