Selling my Mach 1 intake. It has 17k miles on it. The top and bottom of the lid have been polished. The top of the runners accessible under the lid have also been opened up and polished. The lower plenum has been cleaned up with a die grinder through the cup plug holes only. The intake has not...
Selling a terminator coolant crossover tube. Good shape, with new o-rings (all four). Just paid $125 for it on eBay plus $20 for the proper Ford o-rings, but have decided to go with a COT delete setup. $125 shipped obo.
As the titles says. Let me know what you have.
Also looking for a Cobra or Marauder balancer, and a heat exchanger and reservoir. Will consider factory or aftermarket on these.
Selling a set of 7 Weapon X coils. Actually all 8 are there but one needs to be replaced which will cost $55 from various outlets. These are in good shape and have about one year on them (about 5,000 miles). $140 shipped.
PM or text to 714-six seven three-0276 for pics.
These are designed for...
Selling a set of Pacesetter headers in original plastic. Bought for an '04/'04 Mach 1 and never installed. I believe these fit all 4v Mustang applications through '04 and are ceramic coated. Asking $340 shipped.
I have a set of WeaponX coils with about a year of run time on them. One went bad from an installation error - it wasn't pressed down fully on the sparkplug. The rest are perfect and there was a difference in power when the coils were on the car. Single coils are available from Brothers and...
Full non-intercooled "tuner kit" kit. All brackets, bolts, etc. in like-new condition. $2350 shipped. Pics available. The car is not a daily driver and the kit has maybe 500 miles on it. Works fantastic. Reason for sale is to help fund another project.
This setup is brand new in the box. Never installed, mocked up, or ran. It is meant to give you some additional power and MAF headroom while maintaining good drive-ability.
The housing and filter look huge. :beer:
Includes:
100mm MAF housing
'05 Factory sensor
Filter
pigtail (plug...
Fits '96-'04. Motor mounts are for 4.6. Actually fits earlier models too.
Selling a new "Perfect Fit" AFCO k-member kit complete with a-arms and maximum motorsports coil-over kit and springs (front). The k-member was only mocked up and then was removed from the car and the control arms are...
What approximate boost level will it make with a 3.48" pulley?
The car used to have an S-Trim that made 10-11 psi with that pulley.
Will it make less with the SC? I also heard it might come earlier with the SC. Is that true or is the case the opposite?
I have the blower apart for a...
I have a Tremec 3650 out of an '04 Mach 1 for sale. Appears to be in very good condition but I have never run it. Was replaced with a T56, has less than 10k on it. Make offer. Would have to be shipped by truck or picked up.
I have the following for sale:
Solid axle from my '03 Mach 1, 7k miles, 3.55 gears, etc, with axles, but no brake brackets, painted, excellent condition, same width as '99-04. Make reasonable offer.
Two bare 8.8" housings, clean, good shape, same with as '79-'98, works with disc or drums...
Anyone have ideas where I can find factory '96-'98 intake manifold? I need the odds 'n' ends too. This is for a 4V swap into a '98 GT. I have not seen these on ebay lately.
Hi
I'm new to this forum and have some basic Q's.
Assuming an '03 or '04 Lightning, what would be the most reliable way into the 12s? The truck would be daily driven and the fuel mileage would need to stay close to stock.
I was thinking possibly 4lb pulley, JLT or similar, and possibly...
Anybody know who has decent deals for a new L in the San Diego, Orange County, or Riverside areas?
I want to sell or trade my 2,800 mile '03 Mach 1.
Nick