Search results

I had to take mine off for smog, want to put it back on. When I bought it, MAC sent a cheapo flange gasket that I used. I have a new stock flange gasket but not sure if it will work as it is designed for the grove on the stock mid pipe. Any input? Anybody get by with a stock ford gasket with MAC...

hahahahaha

Have any of you had to smog your car yet? Mine will be due in July. I know I'll have to put my stock midpipe on but what about everything else? Stock blower? CAI will probably have to come off as well, right? Running mods in my sig. Thanks.

Is there head unit out there that will replace the factory one without having to change out the stock amps and speakers? Want to hook up an ipod. I ordered an alpine replcaement only to find out you need to replace the amps as well. At least according to Crutchfield. Not looking for subwoofers...

^^^^^ Wtf????:shrug: :nonono:

I asked this over in the exhaust section yesterday with no responses. Right now I am running an off road MAC Pro chamber with stingers. I was wondering if I would have to retune by switching back to my MRT H w/cats. I like both midpipes but am sick of the gas smell when running the off road...

Right now I am running an off road MAC Pro chamber with stingers. I was wondering if I would have to retune by switching back to my MRT H w/cats. I like both midpipes but am sick of the gas smell when running the off road pipe. Do I need to retune? Car has stage IV port with 2.76.

Driving down the road and the wife says "When did this happen?" I look over on the passenger side and see a crack rising up from under the wiper. About 8" straight up:mj: Anyway, anyone know the cost to replace one of these fuggin things? If it was any other car I would say screw it, but it...

Anybody else have one that went bad? I went to tune my car while ago and when I got to the dyno the pump would not come on. I checked it by using a jumper wire. I could hear the pump runing but it wasn't moving fluid. I drove it home and tried again. It worked fine. Did it again, same thing...

Like new $125 PM or email [email protected]

Swaped out my stock blower for a ported one which came with this pully. Keeping my BF 2.76 so I have no use for this pully. 25 bucks takes it. PM or email at [email protected]

When doing my Heat exchanger install this past weekend, I noticed someone busted off my :fm: Anyone know what part number this thing is and where I can get another? I am missing the passenger side fog light bezzle for the front bumper

Got everything on and done. Problem now is there is a lot of slack in the throttle cable. I put it on the same way it came off but now I can pull the cable with no resistance from the engine bay. Seems like the cable grew. There seemes to be no slack when I unhooked it. Does it attach to...

I got the blower off and everything went smooth, Swapping the IC to the ported blower now. I took the IC off no sweat but there is not gasket there. Is there supposed to be a gasket? Looks like there may have been some silicone at one point but it is only at one corner. Do I need to use some...

:fm: So I installed my IRS brace today! Directions were good. Removal of passenger side cat back was a snap. Removal of all the bolts took some time (farkin top bolt and the number 3 bolt). Installation of new bolts went ok minuus the top bolt. Now for the real problem. Could not get my...

Driver side rear wheel sits further back in the fender than the other side. I have = gap on passenger side but driver side rear wheel has a large gap from the front of the tire to the fender and the back of the tire has a small gap to the fender. Car tracks straight but every time I hit a dip or...

Any problems with the speedo being off (Not Calibrated) and gearing problems with these tires? I just ordered 2 for my 18 x 10's and imagine they are going to be a bit taller than the 275 35 18's I have on there now (18 x 9).

Off a 2003 Cobra, only has 1000 miles on shifter. $120 OBO [email protected]

I removed my stock pulley last night. Followed the directions from BF. Mine did not make an loud "pop" when it came off. It was very tight coming off but did after several turns of the bolt. Anyone else not hear a loud pop? Couldn't install the 2.93 due to not having a 7/8 wrench. Picking...

The damn think has a freakin leak!!!! :cuss: Sounds like ass!!! :fm: The install was very easy, 2 hours to include jacking up the car. I don't hear any ticking at idle, but at WOT it sounds like hell. Other than that, it is loud and would sound good if it would seal. Not sure where it is coming...

2003 Cobra 6000 miles Just got my BF 2.93 with 4 idlers (did not install yet) Steeda CAI Stingers Bassani X w/cats (Going to go to H-pipe or back to stock H) My question is who should I see about a tune? What all do I need? What is involved with a hand held? Don't want a canned tune...

CRAP!!!! Rant on Ok, so on Friday I decide to bolt on my X with cats! Pain in the ass! No problem with the bolts on either side but the O2 sensor plugs were a bitch!! Could not grab the plugs and undo them with the tight space. After awhile I got them. Dropped the stock H. Then bolted...

What does it mean when your MAF is pegged? Is it broken? :shrug: I'm only running a CAI and Stingers so I don't have any problems but I was just wondering. Thanks