Search results

Hello, I have a 5.4 navigator engine and a 99 cobra intake that is ported and I have all the parts for. I am need of adapters to make this work. Can anyone sell me the adapter plates that were made by a few people and shops for a while? Thanks, Chris

Hello, I need of 99 Cobra Intake to 5.4 Navigator heads adapter plates. My intake is nicely ported and though I know I could make more power with other intakes, i want to get this combo together and compression test the used engine (with stated 80K miles) before I plow mega $ into it. Please...

I am also looking for the same. Were you able to make some or find a supplier?

Considering a 106160 set of Comp Cams on an Navigator 5.4, can I mill .060 with those?

How about on a 5.4 out of a Navigator. It will probably have 97 Cobra intake cams unless I find a deal on some better ones? I will degree them.

Any issue with PTV clearance when milling heads?

Thanks for the reply! In terms of make sure I didn't get coolant in, I would be able to see right? Meaning things would be cleaner from the steam? There is no coolant coming out of the exhaust and it sounds pretty normal. I can afford downtime. I have another car I can daily.

Hi, Long story short, I was driving my car across country (97 Cobra with an aviator swap), lost an idler pulley and limped it to a Napa auto parts. Engine got a bit hot and hasn't been the same since (runs hot). Other than that, it runs fine. I did a combustion gas test this evening and it...

Car is a bit schizophrenic. Started up today. This has me wondering. If moisture from the storm and large puddles was the issue, it has been hot and it may have evaporated it. I drove the car for about 30 mins and added some engine bay heat in case that helps. I will start it again...

Hi All, I am in Alexandria, VA. I am having some PCM issues in my 97 Cobra. SCT xcalibrator 1. Had some issues getting the car started, got it started once after reloading a tune. Came back a day later, it wouldn't start. I have checked fuses, PATS, ignition module, voltage etc. I am...

Update...back to not working. Smoke cleared, it was the scan gauge smoking in the OBD port. Order of events was, loaded the Factory tune from the SCT Xcalibrator (version 1) and the car worked. Went to drive it today and no dice. Tried to reload the factory or upgraded tune and it isn't...

OK...got it running! Thanks all!!! So what fixed the car...I reloaded the factory tune from my XCal (version 1). My car has an aviator swap with a ported cobra intake and some other light mods, so about 12 years ago, I had a tune for that setup put in. Going to button it up and do some...

A few updates: PATS seems to prove out...meaning I put a key in, turn it forward (but not crank) and the light goes out. I checked all underhood fuses, in particular, the 20 amp fuse in the engine bay fuse block. They all look good. There was a test I found for the PCM that I am going to...

Agreed. I did some more investigation. I had a scan gauge plugged into the OBD2 port to provide me some sensor data while driving. The smoke was coming from there. When I pulled it and tried to start the car, no more smoke, but the car doesn't start. Wondering if it is the PCM, looking up...

Thanks for the prompt reply...i did remove the surround of the steering column. I think I may peel back the wrap around the wires to see if something shorted out. Also, I will pull off the PATS assembly and check those wires. Car has had very few issue over its life, but I drove through...

Guys, Could use some help. Got in my 97 Mustang Cobra (175K mi daily) the other day. It wouldn't start and the steering column was smoking from some melted wires. I disconnected the battery and got to work another way. My first thought was the ignition switch, so I replaced that with a ford...

Having an issue sending a PM. I will take them if you still have them. Thx

IMRC Box from 1997 Cobra with 84K miles when removed. Has been off the car for a few years. $100 obo. Thanks, Chris

Guys, My brother just wrecked an 04 Focus SVT. He would part it out, but isn't that mechanically inclined. Does anyone in FL need a parts car? Thanks, Chris

On old 5.0s you could jump some connections and run a cylinder balance test. Is this possible on 4.6 DOHC? May also do a compression check. Engine has about 80k on it and I want to check its health prior to cams and longtubes. Thanks, Chris

Guys, What is the rubber piece between the c pillar and the quarter panel. I have tried searching. On my pass side, it is sticking out. Any idea where I can get a new one? Thanks

Wanted to Buy A 03/04 Cobra IRS in great shape with brakes, the lower the milage the better. Would prefer stock gears. I have a 97 Cobra Teksid Block I can trade, a set of 97 Cobra heads, some drag radials, or a set of 97 Cobra cams. I am located in Clearwater and prefer you email...