Search results

For Sale – 2003 Mustang Cobra. 66K miles on body and 1K miles on new engine/turbo/suspension. Oxford White. $26K O.B.O.. Engine: Fully built Teksid block 10.5:1 CR Wiseco 2618 forged aluminum pistons Manley “H” beam rods w/ARP bolts Forged steel crankshaft ARP 12pt main studs ARP 12pt side...

Division X hat & Fore rails $ reduced Sold

I have a brand new from ford 4.6 DOHC cylinder head. Casting # RF-2C56-6C064-DC. Passenger side (right side). This is the newest revised casting. I was working on getting a new set of heads and ended up getting a set of MMR stage 3 heads. I no longer need this one. If you have tried...

I have a brand new from ford 4.6 DOHC cylinder head. Casting # RF-2C56-6C064-DC. Passenger side (right side). This is the newest revised casting. I was working on getting a new set of heads and ended up getting a set of MMR stage 3 heads. I no longer need this one. If you have tried...

I have a set of FRPP Camshafts for a 4.6 DOHC. Part numbers are CM-6270-T46, CM-6271-T46, CM-6272-T46, and CM-6273-T46. I am changing to a turbo setup and have purchased the MMR stage 2 cams. $600 + Shipping + Paypal fees. Thank You, Joe Walter 559-772-5617 [/URL][/IMG]

I have a set of DOHC Blue valve covers for sale. $200.00 + Shipping OBO. I am open to any trades. The valve covers have some minor scratches as seen in the pictures. No coil covers. Thank you, Joe Walter 559-772-5617 [/URL][/IMG] P.S. Why does this forum make it so difficult to post...

Got them thanks SVTP

Got them thanks SVTP

I have a 03-04 cobra fuel rail with a good fuel rail pressure switch from my car. I went return and have no need for it. It also has a Kenne Bell disk installed. I am asking $50.00 shipped. You can PM or call me @ 559-772-5617. Thank you Joe Walter Link for picture For Sale 04 Cobra fuel...

I have a used ECU from my 2004 Cobra AMZ1. It will need to be flashed before you use as it is programed with my PATS. If you are using a flash tuner then you will be good to go. It worked fine in my car. I removed it because my tuner thought it was causing a problem with the SCT but as it...

I purchased this fan for my 04 Cobra because my stock fan would not fit with the turbo kit. This fan would also not fit. So my loss is your gain. This info was taken off summit's website. Proform Parts 67015. Electric Fan, Single, 15 in. Diameter, Puller, 2,800 cfm, Black, Plastic, Ford...

I have a set of Roush wheels 18x9 and 18x10. I am looking for $1200.00 plus the ride or Best offer. Any questions please hit me up via PM or email @ [email protected] or 559-772-5617. The wheels are located at my house in Hanford CA. Pick ups are also welcome. Thanks Joe Walter You can...

I have a Precision 70GTSHPSP rated at 850hp. It is a 70mm .75 a/r compressor with 4" inlet and 3" outlet with a T4 inlet 75mm .96 a/r tirbine 3" vband outlet. I would like $750 shipped OBO. It is not going to work for my end HP goals. Turbo was used for a few dyno runs then removed for a 7675...

I have a set of 04 Cobra heads with the 9 thread spark plug hole. I had them resurfaced and was going to use them when I ended up getting a set of ported heads. Heads have 12k miles on them and come with cams. There was nothing wrong with the engine when I pulled them. I just decided to build...

I have an SCT BA-2600 90mm MAF with the aluminum blow thru style housing. This is not the one with the flange and bolt holes. I have gone turbo and need a larger MAF. My car made 601whp in draw thru with a KB 2.6 and the MAF still had plenty of range. $210.00 shipped. Any questions hit me up...

I have been researching how much you can take off the 03-04 cylinder heads. I have found a lot of different opinions ranging from ½ the thickness of the head gasket (.020) to .004. I have some pitting in the combustion area and would like it removed. Why can you only take .020 off? I do not...

Here is one of those mythical Whipple Tensioner. It could use new bolts as the ones with it are worn. It has an adjustment bolt for easier belt installation. This worked the best for me and on a KB 2.6H with 3" upper I never saw any hint of belt slip. Because it is adjustable you can really get...

I have a Kenne Bell 2.6H with 3 pulleys for an 03 – 04 Cobra for sale. It has about 600 miles on it as the car is a weekend only car. The car made 601rwhp on pump 91 on a Dyno Jet @ 17psi. The only mods were a JLT intake, off road “H” Pipe and Borla cat back. I have purchased a Turbo Kit so I...

I have a Kenne Bell 2.6H with 3 pulleys and oval throttle body for sale. It has about 600 miles on it as the car is a weekend only car. The car made 601rwhp on pump 91 on a Dyno Jet @ 17psi. The only mods were a JLT intake, off road “H” Pipe and Borla cat back. I have purchased a Turbo Kit so...

I have a ton of pics but I can't upload them at work. I can however email them upon request. I have a few items up for sale from my 04’ Cobra. All parts are stock and have 18K miles on them. If interested you can PM or post or call me at 559-772-5617. All prices are with out shipping. Buyer...

I have the following parts off my 04 Cobra with 18K on them. Stock Eaton Stock Plenum Stock Throttle Body SOLD Stock 39lb Injectors SOLD Complete Stock intake SOLD Stock MAF SOLD Stock Fuel Pumps SOLD You can reach me via text or PM or email 559-772-5617 / [email protected] All...