04 Cobra Ported Eaton/n20 1/8mi

mustang john

New Member
Established Member
Joined
Jun 2, 2005
Messages
2,168
Location
san antonio, TX
I would think that it should ET alittle better if your really whacking it with a 175 shot. My best 1/8 time was 6.89 @ 99 1.49 sixty with the same ported eaton setup you have minus the spray. But I do have a built SRA and a decently sorted out suspension. Get that sixty down and with the MPH you have it will run 6.6s! Any vids of the run?
 

500hp04cobra

New Member
Established Member
Joined
Feb 7, 2013
Messages
206
Location
Waverly,Ohio
No video. We got some good pics of it leaving.... the ass end actually squatted so hard the irs tailpipes hit...I shouldve specified I was on the 150jets on this run.
 
Last edited:

IronTerp

Mid-Atlantic Cobra Assoc.
Moderator
Joined
Nov 5, 2003
Messages
17,654
Location
State College, Pa
Nice job! That's a 10.6+/- 1/4 mile. Does it have more in it?? Sure. But very nice job and better than a lot of folks that have preceded you! Check out the 60' times on the list below and you'll see where you easiest improvement is going to come from. Very nice job.

THE PORTED/NITROUS/E85 CREW:
1) BADASS03SVT...............9.46 @ 140.84 w/ 1.35 (Auto/SRA)
2) NV2L8ULUZ...................9.83 @ 136.79 w/ 1.375 (Auto/SRA)
3) Posi.............................9.85 @ 140.41 w/ 1.43 (Auto/SRA) (Vert)
4) Clifford from Strictly.......10.01 @ 136.52 w/ 1.4? (Auto/IRS)
5) 03flamedcobra..............10.02 @ 139.59 w/ 1.45 (6spd/SRA)
6) JDM Engineering#1........10.08 @ 136.?? w/ 1.5? (Auto/IRS)
7) CobraStruck..................10.09 @ 134.52 w/ 1.43 (6spd/IRS)
8) SilverSlayerTT...............10.10 @ 138.67 w/ 1.38 (6spd/SRA)
9) VENOMOUS03COBRA......10.30 @ 134.74 w/ 1.51 (6spd/IRS)
10) Sprayed Daily..............10.30 @ 133.63 w/ 1.38 (6spd/SRA)
11) JDM Engineering#2.......10.38 @ 134.?? w/ 1.5? (6spd/IRS) (No port!) (Vert!)
12) Senkak......................10.45 @ 134.40 w/ 1.57 (6spd/IRS) (Vert!)
13) SonicVenum................10.50 @ 131.96 w/ 1.53 (6spd/SRA)
14) darkone19..................10.51 @ 138.80 w/ 1.75 (6spd/SRA) (Upper Pulley)
15) vip3r1850...................10.58 @ 131.75 w/ 1.51 (6spd/IRS)
16) 94-98Transam.............10.59 @ 125.00 w/ 1.51 (6spd/IRS) (No port!)
17) davidsk5018................10.59 @ 131.?? w/ 1.54 (6spd/IRS)
18) BLK_03......................10.61 @ 134.27 w/ 1.60 (6spd/IRS)
19) Broke7.......................10.61 @ 132.00 w/ 1.54 (6spd/IRS)
21) SWEET94COBRA..........10.64 @ 132.64 w/ 1.60 (6spd/IRS) (Vert!)
21) Z-06 Killa...................10.66 @ 130.30 w/ 1.60 (6spd/SRA) (No port)
22) 96stanggt/Magoo........10.71 @ 131.90 w/ 1.69 (6spd/IRS)
23) Mofasta.....................10.77 @ 127.23 w/ 1.49 (6spd/SRA) (No port)
24) foxman92...................10.79 @ 132.76 w/ 1.58 (6spd/SRA) (E85)
25) F8LBITE.....................10.86 @ 126.20 w/ 1.71 (6spd/IRS) (No port)
26) screamngdave............10.88 @ 127.14 w/ 1.64 (6spd/IRS)
27) 1slosnake..................10.89 @ 125.74 w/ 1.74 (6spd/IRS)
28) blownwhite03.............10.89 @ 128.60 w/ 1.68 (6spd/IRS)
29) timspony....................10.89 @ 133.12 w/ 1.56 (6spd/IRS) (E85)
30) AidanN20...................10.90 @ 126.00 w/ 1.55 (6spd/SRA) (No port)
31) iBiTe03......................10.93 @ 126.82 w/ 1.49 (6spd/SRA)
32) baby2000...................10.96 @ 129.29 w/ 1.61 (6spd/IRS) (No port)
33) truebluecobra..............10.98 @ 126.40 w/ 1.63 (6spd/IRS)
 
Last edited:

700hp04Mystic

New Member
Established Member
Joined
Oct 25, 2010
Messages
314
Location
Jackson Ohio
car hauls ass bro, need some more seat time and you will drop et big time. good job!!!!
its easy to say and hard to do is what ive found out.
 

500hp04cobra

New Member
Established Member
Joined
Feb 7, 2013
Messages
206
Location
Waverly,Ohio
Here's a pic of it leaving.

IMG956715.jpg
 

500hp04cobra

New Member
Established Member
Joined
Feb 7, 2013
Messages
206
Location
Waverly,Ohio
Weld RTS 15x8 5.5bs 28x11.50 15 Hoosier qtp. It took us about an hour with a grinder taking off a little at a time and test fitting the wheels. It didnt need as much grinding as I thought it would.
 

Users who are viewing this thread



Top