OK, clearing out the garage of the parts I'd amassed to build this Teksid 4V. Just sold the Gen5 Whipple in the other thread and people had mentioned they might be interested in other stuff. I'd prefer to sell this stuff locally, especially the bigger/heavier things but will ship. Figure PayPal is the easiest and safest means for both buyer and seller. There are tons of little odds and ends that I'm going to list - it would be so much easier to ship lots of things together rather than making daily runs to the post office between long hours at a busy job and family, with the third kid due up in the next few weeks.
Here we go....
Kellogg crank - will need to have the rod journals turned 0.010" under. Threads in the snout are very good. Some surface rust on the counterweights that will come off during the cleaning/machining process.
$400
King CR 868si rod bearings
$30
Ford stamped reluctor wheel
$20
ARP 254-2801 flywheel bolts
$30
Innovators West balancer #813
$450
ID1300cc injectors. Freshly cleaned/flowed with no run time since.
$1000 - SOLD
3V HV/HP oil pump
New in box
Steel back plate
DR3Z-6600-A
$90 - SOLD
ARP head studs 256-4201
Torqued once in cylinder honing process
$375 - SOLD
Teksid block. ~70k miles, pulled from a MkVIII. Bearings all looked perfect. I had it bored 3.554 where it cleaned up to keep as much cylinder wall there as possible. This was done with a torque plate and head studs. I had planned to call and get pistons custom made to fit this bore. The mains were torqued, including the side bolts, and it did not need to be align honed. The entire block has been deburred. All holes (head bolts, main bolts, etc) have been chased (noncutting tap) and cleaned. The front dowel pins have been tapped for the larger steel pins from Cobra Engineering. I have the rear seal. I'm happy to sell the block with the ARP main studs (156-5901)/side bolts (156-5001) as it sits (both sets are brand new).
$900 w/ hardware. Will include M-6026-A46 block kit and new brass freeze plugs.
SOLD
DB cylinder heads
Cam caps/bolts all present. Still assembled with stock valves/springs. I have the lifters and followers as well. Camshaft bearings look very, very good. I can take more detailed photos if I have an interested buyer.
$500 - SOLD
Kellogg crank - looks good/measures out and can be run std/std. Threads in the snout are very good.
$600 - SOLD
03 Cobra cams / sprockets
$50 or free if you buy something else and pick it up lol - GONE
Boundary billet OPG for 3V pump
$175 - SOLD
Felpro head gaskets - 26187 and 26222
$75 - SOLD
Melling JB-2271 lifters (32)
$125 - SOLD
Cloyes S869HP crankshaft sprocket
$60 - SOLD
Accufab billet reluctor wheel
$125 - SOLD
3V windage tray (used) - some surface rust that'll clean off easily
$60 - SOLD
Accufab secondary timing chains
$200 - SOLD
Cobra Engineering billet tensioner
$150 - SOLD
Cobra Engineering drill template with steel pins
$180 - SOLD
Shelby Mike billet timing arms and wear strips - for larger steel pivot pins
$250 - SOLD
Comp 10254 adjustable timing gears (used - 10 miles)
$230 - SOLD
Cloyes stationary timing guides - 95464 and 95461
$30 - SOLD
Gigantic box of Ford parts - oil pump, gaskets, seals, primary tensioners, one secondary tensioner
I'm going to just upload a picture of the part numbers ,along with the actual photo of the parts themselves, to cross-reference
I would prefer to sell this all together; it's all going to be needed if you're building a 4V
$500 - SOLD
ARP AZW200, 300-8305, AQ4.750-1LB
Stud, washer, and nut to use to convert crank to stud-mounted balancer
I had to order these direct from ARP
Will include w crank purchase
$40 - SOLD
Stainless exhaust manifold studs + nuts
$30 - SOLD
4.6 flywheel holding tool
$25 - SOLD
Thanks - Phil
Here we go....
Kellogg crank - will need to have the rod journals turned 0.010" under. Threads in the snout are very good. Some surface rust on the counterweights that will come off during the cleaning/machining process.
$400
King CR 868si rod bearings
$30
Ford stamped reluctor wheel
$20
ARP 254-2801 flywheel bolts
$30
Innovators West balancer #813
$450
ID1300cc injectors. Freshly cleaned/flowed with no run time since.
$1000 - SOLD
3V HV/HP oil pump
New in box
Steel back plate
DR3Z-6600-A
$90 - SOLD
ARP head studs 256-4201
Torqued once in cylinder honing process
$375 - SOLD
Teksid block. ~70k miles, pulled from a MkVIII. Bearings all looked perfect. I had it bored 3.554 where it cleaned up to keep as much cylinder wall there as possible. This was done with a torque plate and head studs. I had planned to call and get pistons custom made to fit this bore. The mains were torqued, including the side bolts, and it did not need to be align honed. The entire block has been deburred. All holes (head bolts, main bolts, etc) have been chased (noncutting tap) and cleaned. The front dowel pins have been tapped for the larger steel pins from Cobra Engineering. I have the rear seal. I'm happy to sell the block with the ARP main studs (156-5901)/side bolts (156-5001) as it sits (both sets are brand new).
$900 w/ hardware. Will include M-6026-A46 block kit and new brass freeze plugs.
SOLD
DB cylinder heads
Cam caps/bolts all present. Still assembled with stock valves/springs. I have the lifters and followers as well. Camshaft bearings look very, very good. I can take more detailed photos if I have an interested buyer.
$500 - SOLD
Kellogg crank - looks good/measures out and can be run std/std. Threads in the snout are very good.
$600 - SOLD
03 Cobra cams / sprockets
$50 or free if you buy something else and pick it up lol - GONE
Boundary billet OPG for 3V pump
$175 - SOLD
Felpro head gaskets - 26187 and 26222
$75 - SOLD
Melling JB-2271 lifters (32)
$125 - SOLD
Cloyes S869HP crankshaft sprocket
$60 - SOLD
Accufab billet reluctor wheel
$125 - SOLD
3V windage tray (used) - some surface rust that'll clean off easily
$60 - SOLD
Accufab secondary timing chains
$200 - SOLD
Cobra Engineering billet tensioner
$150 - SOLD
Cobra Engineering drill template with steel pins
$180 - SOLD
Shelby Mike billet timing arms and wear strips - for larger steel pivot pins
$250 - SOLD
Comp 10254 adjustable timing gears (used - 10 miles)
$230 - SOLD
Cloyes stationary timing guides - 95464 and 95461
$30 - SOLD
Gigantic box of Ford parts - oil pump, gaskets, seals, primary tensioners, one secondary tensioner
I'm going to just upload a picture of the part numbers ,along with the actual photo of the parts themselves, to cross-reference
I would prefer to sell this all together; it's all going to be needed if you're building a 4V
$500 - SOLD
ARP AZW200, 300-8305, AQ4.750-1LB
Stud, washer, and nut to use to convert crank to stud-mounted balancer
I had to order these direct from ARP
Will include w crank purchase
$40 - SOLD
Stainless exhaust manifold studs + nuts
$30 - SOLD
4.6 flywheel holding tool
$25 - SOLD
Thanks - Phil
Last edited: