Home
What's new
Latest activity
Authors
Store
Latest reviews
Search products
Forums
New posts
Search forums
What's new
New posts
New listings
New products
New profile posts
Latest activity
Members
Current visitors
New profile posts
Search profile posts
Log in
Register
Cart
Cart
Loading…
What's new
Search
Search
Search titles only
By:
New posts
Search forums
Search titles only
By:
Menu
Log in
Register
Navigation
Install the app
Install
More options
Change style
Contact us
Close Menu
Forums
Cobra Forums
The Terminator
Driveline
Need wiring help with Termi auto swap.
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Reply to thread
Message
<blockquote data-quote="r1cefed" data-source="post: 14541762" data-attributes="member: 131064"><p>I am in the process of doing an auto swap on my 03 Cobra. I am using a Lentech Street/Strip 4R70W with a Precision converter. The plan was to use the Mach 1 ECU, trans harness, and body harness (the harness that runs down the passenger side fender). I have done numerous searches but cannot seem to find any support on wiring besides how to change the plug on the trans harness. Most posts I found on other forums had the pictures removed for some reason.</p><p></p><p> My goal is to use the Mach 1 ECU to shift/lockup the Lentech. I am not using a MVB setup like most are doing. However I am at a dead end with the wiring. Here are some of my major questions. (Feel free to PM me as well if that is easier)</p><p></p><p>1. Are the harnesses that I listed the only ones necessary to make the swap work? I am already aware of the heat exchanger pump and IAT sensor issues. I just need to know if I need any other harness to make this happen.</p><p></p><p>2. If I cut and swap the plugs off the transmission harnesses I have multiple wires left over. (Roughly 5 or 6) I am assuming these will be what controls the shifts/solenoids. What do I wire these to?</p><p></p><p>3. There are a couple of extra plugs on the Mach 1 body harness that are not on the Termi harness. (I can take pictures if necessary) I would just like to know if they will be used for anything or not.</p><p></p><p>In a nutshell I really just need to know if I need to repin anything on the harness to make the car shift. I am extremely lost at this point and cannot go further with the project until I get on track with the wiring. I am assuming the left over wires from the trans harness after I swap the plug will make it to the ECU I just need to know how. If anyone has a link to a write up or a pin out/diagram the help would be greatly appreciated. </p><p></p><p>I am not sure why I cannot find anything even through Google on this subject. Most people seem to be using the Baumann controller or simply just using an MVB transmission. Any link I find involving a Mach 1 ECU seems to be gutted of pictures/info.</p><p></p><p>Thanks again.</p><p></p><p>Matt.</p></blockquote><p></p>
[QUOTE="r1cefed, post: 14541762, member: 131064"] I am in the process of doing an auto swap on my 03 Cobra. I am using a Lentech Street/Strip 4R70W with a Precision converter. The plan was to use the Mach 1 ECU, trans harness, and body harness (the harness that runs down the passenger side fender). I have done numerous searches but cannot seem to find any support on wiring besides how to change the plug on the trans harness. Most posts I found on other forums had the pictures removed for some reason. My goal is to use the Mach 1 ECU to shift/lockup the Lentech. I am not using a MVB setup like most are doing. However I am at a dead end with the wiring. Here are some of my major questions. (Feel free to PM me as well if that is easier) 1. Are the harnesses that I listed the only ones necessary to make the swap work? I am already aware of the heat exchanger pump and IAT sensor issues. I just need to know if I need any other harness to make this happen. 2. If I cut and swap the plugs off the transmission harnesses I have multiple wires left over. (Roughly 5 or 6) I am assuming these will be what controls the shifts/solenoids. What do I wire these to? 3. There are a couple of extra plugs on the Mach 1 body harness that are not on the Termi harness. (I can take pictures if necessary) I would just like to know if they will be used for anything or not. In a nutshell I really just need to know if I need to repin anything on the harness to make the car shift. I am extremely lost at this point and cannot go further with the project until I get on track with the wiring. I am assuming the left over wires from the trans harness after I swap the plug will make it to the ECU I just need to know how. If anyone has a link to a write up or a pin out/diagram the help would be greatly appreciated. I am not sure why I cannot find anything even through Google on this subject. Most people seem to be using the Baumann controller or simply just using an MVB transmission. Any link I find involving a Mach 1 ECU seems to be gutted of pictures/info. Thanks again. Matt. [/QUOTE]
Insert quotes…
Verification
Post reply
Forums
Cobra Forums
The Terminator
Driveline
Need wiring help with Termi auto swap.
Top