OVER 800HP TO THE WHEELS?! Part 2 - Whipple Supercharged 2024 Mustang GT on the dyno!

[Jake@Lethal]

Hey, ALL!
Well, the rev limiter has been fixed and we're back at Palm Beach Dyno for Part 2 of our Whipple Supercharged 2024 Mustang GT dyno testing. Will we crack that 800+ wheel horsepower number?! This is a 6-speed 2024 Mustang GT using the Whipple calibration on 93 octane. We installed a Stage 2 Whipple Supercharger kit with the Gen 6 3.0L supercharger and are using a Griptec 3.75" pulley, which is the standard size in their Stage 2 kit, as well as 3.625 Griptec pulley later on.

We also have a set of Kooks 1 7/8" Long Tube headers, a Corsa HH-pipe, a Mcleod RXT clutch, MGW X-Spec Shifter, G-Force Outlaw Axles, and a QA1 Rev Series Carbon Fiber driveshaft. On the 3.75" pulley, along with 16oz of VP Octanium Unleaded, we made a solid 807 WHP and 635 WTQ. Per the datalogs, this is roughly 12 lbs of boost at its peak. On the 3.625" pulley along with the same 16oz of VP Octanium Unleaded, we made 833 WHP and 661 WTQ, just barely peaking at 13 lbs of boost. Now that we have some solid dyno numbers, it's time to hit the drag strip!

​

 

[Jake@Lethal]

Hey, ALL!
Well, the rev limiter has been fixed and we're back at Palm Beach Dyno for Part 2 of our Whipple Supercharged 2024 Mustang GT dyno testing. Will we crack that 800+ wheel horsepower number?! This is a 6-speed 2024 Mustang GT using the Whipple calibration on 93 octane. We installed a Stage 2 Whipple Supercharger kit with the Gen 6 3.0L supercharger and are using a Griptec 3.75" pulley, which is the standard size in their Stage 2 kit, as well as 3.625 Griptec pulley later on.

We also have a set of Kooks 1 7/8" Long Tube headers, a Corsa HH-pipe, a Mcleod RXT clutch, MGW X-Spec Shifter, G-Force Outlaw Axles, and a QA1 Rev Series Carbon Fiber driveshaft. On the 3.75" pulley, along with 16oz of VP Octanium Unleaded, we made a solid 807 WHP and 635 WTQ. Per the datalogs, this is roughly 12 lbs of boost at its peak. On the 3.625" pulley along with the same 16oz of VP Octanium Unleaded, we made 833 WHP and 661 WTQ, just barely peaking at 13 lbs of boost. Now that we have some solid dyno numbers, it's time to hit the drag strip!

​

Today, Jared takes our Whipple-Supercharged 2024 Ford Mustang GT to RSA Race Solutions in Boynton Beach, FL to install the Corsa Performance Xtreme Cat-Back Exhaust.

We start off with overview of the Axle-back portion, which in pair with the already-installed Double HH Pipe, will make this a FULL Corsa Xtreme Cat-back Exhaust. After roughly an hour of wrenching on the car, walking you through each step of the installation, we give a nice cold start and run it through the various modes. Lastly, we give a healthy selection of exhaust notes in all modes, from fly-bys, to revs, and launches.

Check out the video below!

​