Revan Racing 13-6?

[STCobra]

Any 1/4 mile times? ET/MPH?

 

[scottGT500]

Sub'n...

I tried with my 13-6 on stock tires...and 95 degree Memphis heat. IAT reading was anywhere from 130-141 degrees from waiting in line so I was in "limp" mode timing-wise lol...wasn't pulling hard at all.....

Best 11.7@125 2.13 60'

Scott

 

[Derek5774]

I ran 11.3 at 127 on street tires with a horrible 60 ft of 2.03
felt like I was spinning most of the way,
with drag radial's it could have ran 10's

 

[NIXDSG]

ok, got me REAL interested. 11.7 w/ 2.1 and 11.3 w/ 2.0? Not sure those make sense, but interested just the same. Anything mid 11's on street (original stock?) tires has me interested!

I didn't want to read this thread.

 

[scottGT500]

I can't wait until I can do a run in COOLER weather (and better tires)! No way I shouldn't have a 132ish mph car...my car is COMPLETELY different sub 75 degrees....obviously.

Scott

 

[Derek5774]

ok, got me REAL interested. 11.7 w/ 2.1 and 11.3 w/ 2.0? Not sure those make sense, but interested just the same. Anything mid 11's on street (original stock?) tires has me interested!

I didn't want to read this thread.

The driver has alot to do with it
Because it is a job to get that car to move with that kind of power on street tires
Put some drag radials and it will hook and go

 

[scottGT500]

The driver has alot to do with it
Because it is a job to get that car to move with that kind of power on street tires
Put some drag radials and it will hook and go

Derek: what is your new setup? I am debating going KB...

:beer:

 

[Derek5774]

Derek: what is your new setup? I am debating going KB...

:beer:

Kenne Bell 3.6
Long tube headers
BMR rear suspension and BMR K-member
Competition heat exchanger

Those are the main mods

It makes 740 whp at 16.5 psi on pump gas
And always above 700 even heat soaked

 

[scottGT500]

Kenne Bell 3.6
Long tube headers
BMR rear suspension and BMR K-member
Competition heat exchanger

Those are the main mods

It makes 740 whp at 16.5 psi on pump gas
And always above 700 even heat soaked

Very nice sir! Van told me about your setup...very impressive to say the least! How much Torque with the 3.6 @16.5lbs? Which hood did you go with? I am getting close to changing my setup...:rockon:

Scott

 

[BITDIFFERENTSVT]

Subing

 

[72SBC]

I went 11.70@127 on stock tires. 2.2 60 foot. Intake temp was 180ish, and it was 95+ outside. Oh and on 91 octane. I'm confident with a good tire and cooler temps I'll go high 10's. I have a 100 oct tune I haven't even tried yet. Stock pulley also. 13-6 kit does wake the car up.

 

[Derek5774]

Very nice sir! Van told me about your setup...very impressive to say the least! How much Torque with the 3.6 @16.5lbs? Which hood did you go with? I am getting close to changing my setup...:rockon:

Scott

I don't remember what the torque was
I went with the super snake hood with pins

 

[Tytus2012]

I ran a 11.6 @ 127 mph 2.0 60 ft with the 13-4 kit ( stock tb) . I also did this on the stock tires. I hadn't ran a car out there in 6 years. I feel with the tb and more ride time I could hit low 11s

 

[BIRDDOC]

I ran a 10.7 at 134 with 305/20 MT drag radials. This was before wt reduction and E85. Had 15% OD pulley.
Had basic suspension mods: BMR LCA/UCA/Panhard.

 

[Lethalchem]

I ran a 10.7 at 134 with 305/20 MT drag radials. This was before wt reduction and E85. Had 15% OD pulley.
Had basic suspension mods: BMR LCA/UCA/Panhard.

I think that was before your gears too, wasn't it?

 

[BIRDDOC]

I think that was before your gears too, wasn't it?

That was with 3.73's

 

[Fastfish420]

I went 11.50 at 125 on very hot temps also spinning and missing 2nd gear.running it again Friday night!

 

[BossAnaki]

I ran a 10.7 at 134 with 305/20 MT drag radials. This was before wt reduction and E85. Had 15% OD pulley.
Had basic suspension mods: BMR LCA/UCA/Panhard.

Was that pump or race gas?

 

[BIRDDOC]

Was that pump or race gas?

Race gas but tune was street conservative. 720 WHP

 

[Fastfish420]

Ran mine tonight and went a 11.23 at 129.50 with 2.07 60 foot time and this is with drag radials.