ATI Superglide 2 Powerglide Transmission with Mod motor bell housing. 15 passes on the tranny
http://www.atiracing.com/products/trans/pg/superglide2.htm
With
ATI SCS-30 Cooling System for Powerglide Transmissions / Such a sick design.
Read up on it here!!
http://www.atiracing.com/products/trans/transparts/scs30.htm
- PTC top of the line 9.5 inch converter.. 5 passes on converter / Had another converter that used for the other 10 passes... This one is dead on for a mod motor..
- Built for turbo suetup behind a 5.4 / 4.6 -
- JW the wheel Flex plate.
- Locar Flexable anchor tight dipstick...
- Lube locker tranny gasket..
I have over 7k in this setup..
5k Shipped to your door...
Max HP
2,400 HP
Still in car, but fresh with 15 passes on it.. Pulling this weekend and will have it gone through to make sure it is perfect.. It was behing my 1k HP mod motor so I am sure it is still mint.
Tranny Specs
• Vasco Gear Set - 1.80 ratio
• Precision Balanced 4340 Carrier & Output
• Exclusive 30 Spline Turbo Clutch Hub, Input Sun
Gear and 1" Ringless Vasco Input Shaft
• ATI SuperCase and Tail housing
• Compu-Flow Pro Style Forward Manual Transbrake
• 10 Clutch High Gear Drum
• Turbo splined clutch hub
• Premium Competition Friction Lined Super Band
• Heavy Duty 4140 Band Adjuster
• Wicked Quick Billet Aluminum Valve Body
• Aluminum Super Pump with matching Stator for
Ringless Shaft
• Billet Twin Seal Servowith Gapless Rings and cover
• Integral Transmission Catch Can
• Deep Cast Aluminum Pan
• High Performance Gaskets and Seals
• High flow filter system
• -6 AN Fittings standard
• Multi Lever
• Case to Bell Stud Kit
• Bearing in Case for Output Shaft
• Heavy Duty Extension housing
http://www.atiracing.com/products/trans/pg/superglide2.htm
With
ATI SCS-30 Cooling System for Powerglide Transmissions / Such a sick design.
Read up on it here!!
http://www.atiracing.com/products/trans/transparts/scs30.htm
- PTC top of the line 9.5 inch converter.. 5 passes on converter / Had another converter that used for the other 10 passes... This one is dead on for a mod motor..
- Built for turbo suetup behind a 5.4 / 4.6 -
- JW the wheel Flex plate.
- Locar Flexable anchor tight dipstick...
- Lube locker tranny gasket..
I have over 7k in this setup..
5k Shipped to your door...
Max HP
2,400 HP
Still in car, but fresh with 15 passes on it.. Pulling this weekend and will have it gone through to make sure it is perfect.. It was behing my 1k HP mod motor so I am sure it is still mint.
Tranny Specs
• Vasco Gear Set - 1.80 ratio
• Precision Balanced 4340 Carrier & Output
• Exclusive 30 Spline Turbo Clutch Hub, Input Sun
Gear and 1" Ringless Vasco Input Shaft
• ATI SuperCase and Tail housing
• Compu-Flow Pro Style Forward Manual Transbrake
• 10 Clutch High Gear Drum
• Turbo splined clutch hub
• Premium Competition Friction Lined Super Band
• Heavy Duty 4140 Band Adjuster
• Wicked Quick Billet Aluminum Valve Body
• Aluminum Super Pump with matching Stator for
Ringless Shaft
• Billet Twin Seal Servowith Gapless Rings and cover
• Integral Transmission Catch Can
• Deep Cast Aluminum Pan
• High Performance Gaskets and Seals
• High flow filter system
• -6 AN Fittings standard
• Multi Lever
• Case to Bell Stud Kit
• Bearing in Case for Output Shaft
• Heavy Duty Extension housing