Recent content by Undy

Turn-coat, traitor, a$$hole among other discriptive adjectives comes to mind when I think of the replies I'll probably get.. First off let me go on record saying that my 03 Cobra, bar none, has been the best high performance car that I've ever owned. It has been perfect in every way and has...

I had the car in the air on 4 jack stands doing a tranny fluid swap from D4 back to Dextron III and checking the diff fluid level.. ( I recommend everyone periodically check it, mine was a half pint low!) I fired the car off and let it idle for a while to check for leaks etc. While the car was...

People are still asking.... http://svtperformance.com/forums/showthread.php?s=&threadid=74143

I just finished the install of my Gords HE. Three words.... piece of cake. It took one hour. I can see no value in taking off the front bumper for the install. Gord definately need to provide a 90 deg elbow for the passenger side upper hose. I used three hose clamps around the hose to keep it...

I've gone through my second set of 315/35/17 BFG KDs. BFG is out of stock on the right tire with no date for availability. I'm looking for a cost effective alternative to the KDs. Tire Rack recommended the Sumitomo HTR Zs. He said the widths, etc is comparable with much better wet weather...

I just would like to thank all the vendors responsible for the awesome numbers my 03 turned on the dyno today, 529rwhp and 522 rwtq SAE. Amazing is the only word that comes to mind. I'd like to thank Brian at Apten for a ported Eaton that damn near puts out like a KB (up to 15lbs that is..)...

For those with the aftermarket idler pullies these are the best bearings to use when yours get "tired". They're especially designed for high rpm, heat and load useage, much better than the OEM bearings. Cost is between 6$ to 10$ from bearing supply houses. I got the mfr/part number from...

Just got back from the Dyno shop and am v-e-r-y pleased with the results after the most recent mods.. Let me devulge all my mods and post the dyno sheet. All figures are SAE.. mods: Amazon Racing single program street Delta chip Amazon Racing CAI Bassani catted X pipe w/ cat back...

Has any one on the board had any problems with their Bassani cats going bad/falling apart? I've been noticing a rattling, mostly at low RPMs when I give the engine a rev. At first I thought it might be the infamous TOB problem but it just didn't follow the pattern, no squeal, did it the same w/...

If it weren't for bad luck...... I was driving home from the Saturday evening hot rod hang-out and I ran over something that banged like hell under the car, scared the sh!t outta me. It was dark and I didn't see a thing at first but when I looked in my rear view I saw something rolling to the...

Last Friday I ordered an Accufab polished TB and polished plenum from Terry@SFPHQ. Low and behold it was delivered today, Monday. How's that for customer service!! He had to grab the TB, rush to wrap it and run it down to the post office. He's the easiest vendor to talk to and get hold of that...

I just picked up the wheel spacers from the machine shop. One word sums them up p-e-r-f-e-c-t! They are truly hub concentric with zero play, in fact in the wheel they have 0.001" interference fit. They are "locked in" when the lug nuts are tightened and essentially become part of the wheel. I've...

I've got a local custom machine shop the specializes in fabrication of automotive racing type stuff. They've done work for me before and their products/service are top notch. They are willing to custom fabricate a pair of hub-concentric 7/32" thick aluminum billet wheel spacers to fit my 03. He...

To my knowledge I'm the second one that has had the following happen.. Let me set the stage for a scary story... I run the AFS 17x10 standard finish 03 Cobra wheels with the BFG KD G-Force 315/35/17 tires in the rear with the BFG KD G-Force 275/40/17s in the front. I also run Mr. gasket...

Those interested have been watching the ongoing process of me getting the 10 1/2" wheels to fit without any "contact" worries. Now.....as far as I'm concerned. it's fixed! For those who don't know I'm running the BFG G-Force KDs 315/35/17 tires. They're the widest 315s I've found thus far. I...