it's an 01 cobra. It has a 5.0 MMR cammed engine and a tremec T56. The tremec solenoid already went bad and replaced so my guess is the Reverse Back-Up Light Lamp Switch. I already ordered it, should be swapped soon. Thanks for your reply.
My reverse lights started flickering at the same time, same pattern. My backup camera (aftermarket) used to work in reverse but it stopped working as well. Any ideas where to start?
My yellow top died and when I replaced the battery, my car did not start. I have the Lethal Performance 99-04 4V Budget Return Style Fuel System (Cobra / Mach-1). I checked all the connections, fuses in the trunk (for the fuel system) under the steering wheel, under the hood (by the battery)...
I need a place or person who can remove a dent on my car. I know dent wizard and the dealers do it but trying to get someone recommended. Thanks
I live in Silver Spring, MD. Thanks
I have an 03 terminator convertible and just bought corbeau seats. I'm trying to figure out how to set up the harnesses since I don't have a roll cage, I only have the CDC light bar. I haven't purchased the harnesses yet.
Pictures are worth 1000 words, if you have them.
Thanks
:shrug:
I just replaced my seats and they are taking some space in my garage. I'm selling them for $500 (front seats only), they are original and in great condition!!!
Will ship if you pay for it.
Library Slideshow by tortolerito | Photobucket
:beer:
I just replaced my seats and they are taking some space in my garage. I'm selling them for $500 (front seats only), they are original and in great condition!!!
Will ship if you pay for it.
Library Slideshow by tortolerito | Photobucket
:beer:
I just replaced my seats and they are taking some space in my garage. I'm selling them for $500 (front seats only), they are original and in great condition!!!
Will ship if you pay for it.
http://s1176.photobucket.com/user/tortolerito/slideshow/
:beer:
I'm selling a Borla Atak (IRS) 99-04 mustang. I had them installed with my old setup. I only had them for 1200 miles, they are stainless steel and look brand new. I'm asking for $600.
I'm selling a Borla Atak (IRS) 99-04 mustang. I had them installed with my old setup. I only had them for 1200 miles, they are stainless steel and look brand new. I'm asking for $600.
I have a speedhut revolution oil pressure gauge that stays at 100. I tried to reset it holding the button while off and turning on the power for 12 seconds but it only goes down to 40. Who knows how to adjust these gauges? Thanks
I'm selling my 03/04 aluminator short block with less than 1200 miles on it. It is made of aluminum with forged internal parts. Feel free to contact me if you have any questions!!!
Price dropped to $2700
I'm located in MD.
SOLD -----I'm selling my used 3650 trans (5 speed) (upgraded to 26 spline by Bill Wise), with a MGW short shifter, a "Blue Printed" Hi-Rev Pro Motion Performance clutch and a aluminum driveshaft for $1000.
SOLD ----Custom Cams
03/04 Aluminator short block (natural aspirated) with less than...
I'm selling my used 3650 trans (upgraded by Bill Wise), with a MGW short shifter and "Blue Printed" Hi-Rev Pro Motion Performance clutch. I also have an aluminum driveshaft for this trans.
I'm also selling a stage 1 custom cams, these cams were built to be used with factory springs and...
I had my 4.6 with cams stage 1 and a ported eaton with ARH headers and H pipes catted, Borla ATAK and the switched to Flowmaster Exhaust. The sound difference was noticeable but the drone sound on the ATAK was killing it. The flowmaster are way quieter and deliver a better sound. The new 5.0...
What agency do you recommend to work for in FL? Feel free to send me a PM. Currently work in MD in for a big department but looking for a more affordable area to live, less traffic and better weather. Thanks.
I'm selling my Borla ATAK for $500 with less than 1000 miles, American muscle sells them for $824.99. Feel free to ask questions. Borla ATAK Mustang Catback Exhaust 140446 (99-04 Cobra) - Free Shipping 140446
I rather local sells, since I dont want to deal with shipping. It is located in...
I'm selling my Borla ATAK for $500 with less than 1000 miles, American muscle sells them for $824.99. Feel free to ask questions.
I'm is located in Burtonsville, MD (2 minutes away from I95/198).
Who knows a reliable person who can build a custom desktop in the DMV area? Know what I want but can't put it together on my own!!! Let me know, Thanks!!!
Who knows a reliable person who can build a custom desktop in the DMV area? Know what I want but can't put it together on my own!!! Let me know, Thanks!!!