About 1000 miles ago I installed a
Ported blower
Accufab tb/plenum
BA2600
60# injectors
KB BAP
After the retune the car ran great. As of recently, the alternator is starting to go bad and I'm getting low voltage if I start to get on it. When the voltage drops when I'm kind of getting on it...
So recently I just installed a FRPP diff cover and did MM front and rear poly bushings. Last night I was testing my new n2mb wot box and I was doing flat foot shifting when my diff seal blew. I checked it today and 1 bolt is gone, and three are backed out halfway....
I sealed the diff with...
Installed WOT Box and now my car is misfiring at idle and when I rev through RPMs. When car is in the on position, box flashes when gas depressed then stops flashing for a second when I hit clutch. Everything seems to be installed correctly so I'm unsure what it could be. Car drove just fine...
I have a 15x9 with 5.5 backspace and just curious if a 325/50 will fit. I have rolled fenders, IRS bolt. I know the tire is a bit over kill for what I need it for..
Doing a ford racing diff cover install and bushings. I did not do the aluminum diff bushings front or rear. I replaced the stock rear bushing with a new maximum motorsports bushing. They say the cover does not need to be milled to fit with stock bushings.
Attempting to to line up the two rear...
Looking to upgrade my toe links. Couldn't find much about the differences between the two.
Are they both small enough to fit a 15" wheel?
My front diff bushings are worn and needed replaced. I've read that FTBR solid bushings makes a lot of clunks and noises. It also looks like steeda was...
Jokerz Performance Port w/ 2.76 Pulley
Accufab Throttle/Plenum
Intake
Stock Manifolds/Catless X/Borla Stingers
60lbs Injectors
Ba2600
KB BAP
Stock Lower
VMP Dyno Tune on 93 octane
515/502 . Not bad for stock manifolds/lower and 147k miles
https://youtu.be/OoS_zvj2V6c
(unsure how to post the...
All parts were pulled off of my car in 100% working condition. All parts listed were swapped for upgraded parts is the reason for selling.
Stock 03 cobra MAF - 50$ shipped
Coil covers (2 sets) - 60$ shipped a set
Stock hood vents - 50$ shipped
Supercharger/Plenum/ThrottleBody/3.1...
Recently got a single aeroforce gauge installed and had no issues. Then bought a new optima red top battery. About a week and a half later my second aeroforce w/ afr adapter came. Now I have dual aeroforce setup with the afr adapter installed. I'm using a fuse tap into the traction control, and...
Just as title states. Looking for any of these parts in great condition. Will update list whenever I buy a part.
BA-2600 MAF
JLT RAI (gen2)
Located in Orlando, Fl
Looking to buy a set of valve covers. Just bought some cop cover, so no need for them.
I would prefer unpainted but will buy if they are looking for flat black or dark gray
Was trying to find information about the correct size bleeder screws for the 03 cobra front and rear calipers. All the info I found doesn't match eachother.
I got a set at auto zone that was m10x1.0 35mm long but only half of it goes in and stops. I've read that other sizes were 33mm but that...
Miro 398 Matte Black
18x9.5 +34mm
18x10.5 +20mm
265/35 Michelin Pilot Super Sport
305/35 Mickey Thompson Super Sport
Purchased the wheels and tires new 750miles ago. Wheels have slight wear down in the lug hole from the lugs. Other than that they are flawless. Rear tires have a small...
Working on changing the rear brake lines for stainless steel. While removing the hardline, it twisted the hardline and cracked it just above the bolt that holds the line in it. Not sure how I would go about repairing this. Advice?
Was going to get some NT03's. Decided on these. A bit different. It's hard to get a good picture via phone camera for black wheels. Will update with quality pictures one day.
Working on making a custom center cap, matte black with gloss black SVT
http://imgur.com/vAeN0rX...
a set of 94-04 Mustang Saleen wheels in chrome finish with tires. Wheel faces are flawless. Lug holes have some wear. No chrome pitting, no scratches. Come with original modified SVT center caps, also have the OEM backs to the caps too.
18x9 w/ 265/35/18 Nitto NT555 (40% tread life)
+24mm...
Within the past few months I've just been replacing the stock (140k) front suspension components. I have done aluminum rack bushings, bumpsteer kit, inner tie rods, sway bar bushings, end links/bushings, ball joints. Yet I still have this clunk in the front end while turning.
While the car...
Having a hard time finding any reviews for these. I have a new wheel setup and debating on these or just go with r888. Car makes 465/480 and will hardly do any digs until I start on doing suspension next
Looking to purchase a 15x10 weld rts s71 (6.5" backspace/21mm offset) and either put a 295/55 or a 275/60 Mickey Thompson Street S/S.
I had a couple questions.
I know about grinding to fit the rears. But will they fit a 295, no rubbing on a h&r race spring.
Will using a 17x9 wheel up...
Sometimes when I let off while I'm gear, it sounds like my engine/transmission is rocking. Hard to pinpoint it but it sounds like it's just in front of the shifter
In the next couple months I was gonna order a new wheel/tire setup.
Enkei NT03
18x9.5/10.5 offset 27front 30rear
I would rather get a 35 sidewall but I'm a fan of a thicker sidewall. I get a decent discount on nitto tires and was gonna get
275/40/18 nt05 fronts
315/40/18 nt05r rears...
I have a 2003 cobra with the typical driver side bolster rip in it. Anyone go through the trouble of getting only that part of the seat fixed? Only part of my seat that has wear