Selling my on3 twin kit. Buyer will need to get the on3 ac line and brake lines to complete this kit, otherwise it's all here plus extras!
Eboost2 with dual quad port solenoids (Turbo housings are already tapped with fittings)
Vacuum Block
Twin 62 mils with upgraded K&N filters
Heat wrapped...
So in my last mustang I was totally fine changing the headunit. I used A JBL 4 way amp to power a 12" JL sub and my 5x7 JBL front coaxes. The pioneer headunit powered my rears and door subs. The headunit could control high and low pass filters, advanced EQ settings, and bass control for the sub...
Can someone post a pic or two of their car's rear end with BOTH lca and sway bar relocations? I have the fays2 watts link and want to see if all that will live together to run 15x10s.
My car turns left any time the tires break loose either in a burnout or going down the road. Is there something I don't have adjusted right in my suspension or is it unavoidable?
Just thought I'd put my .02 cents in on this install. Wasn't super bad, but definitely could've been easier.
The driverside wastegate location is pretty terrible. Even with the spacer you will have to put a notch in your paper-thin clamp to get it to fit over the flange, but between the...
Not sure where to post this, but here goes.
2011 manual GT. Cruise control stopped working. Light wont come on in dash or work. How do I check for issues/fix this?
I need to have a starting tune for my twin turbo on3 car ASAP. I'm doing the install at my uncle's and need to be able to drive home by tomorrow. We aren't finished yet, but will be by tomorrow. I want to use mastwolf (Chris at ForcedMotorsports), but he's out of the country now so I haven't...
Can someone please post the instructions that come with the on3 kit? My cd is blank... I know the big stuff but don't want to miss something "small" but important that may be common knowledge or whatever to some.
Starting my install tomorrow, thanks.
PREFACE- I am having trouble figuring out all the different vacuum distribution stuff for a turbo setup in general so any helpful links to that would be greatly appreciated. I bought a vacuum distribution block to help clean things up whenever I get it all figured out. This is for a 2011 5.0...
PREFACE- I am having trouble figuring out all the different vacuum distribution stuff for a turbo setup in general so any helpful links to that would be greatly appreciated. I bought a vacuum distribution block to help clean things up whenever I get it all figured out. This is for a 2011 5.0...
[Applies vaseline to anus, checks to see if properly lubricated, satisfied, prepares anus for onslaught]
Is it possible to use the stock 02s and the SCT Livewire tuner to monitor AFR when going FI? I've read that the 2011+ mustangs have this capability from the factory? Don't want to buy...
Could we try to make this a sticky? I'd like to get a concise thread going on what hardware to replace/mods to make with the on3 kit. I'm not talking about other system componemts like injectors, etc. What hardware specifically did you replace and how did you incorporate it.? I do not want this...
Why can't after you "forge" the motor and replace the internals, valve springs, studs, etc. rev the motor to 10k rpm? What is the deal if you have an engine control unit capable of adjusting engine parameters to do so? If the factory ECU isn't capable of doing so why isn't there an aftermarket...
I know there is probably a simple answer out there, but haven't really gotten my question answered from previous threads.
QUESTION: Is it worth it to upgrade the fuel system to a return system and/or go forged internals when I only have 93 octane available to me? Wish E85 was available, but...
Trying to have a concise thread for turbo coyotes! What are your current/past turbo specs? Brand, bearing type, wheel material, compressor, turbine, A/R, HP, TQ, PSI, RPM @ full boost?
Boss Manifold (install kit included is preferred)
Id1000s
Unlocked/Unmarried SCT Livewire (window mount & USB cable included)
feel free to contact me via PM, Post Here, or phone two5two 3four1 4eighteight5
At what boost level from a PD blower with stock manifolds, heads, cams but a forged 9.5 compression bottom end on 93 octane will the coyote stop making more power?
Have you guys seen these?
http://www.allfordmustangs.com/forums/2011-2014-mustang-talk/891761-dob-manifolds-coyote.html#post7838177
I was curious about what everybody else had done to get 600+ RWHP because that's my bottom goal, and I just saw where this guy makes these manifolds that let you...
Have really been wanting to see one installed on a 2011/12 since they came out, but haven't been able to find any pictures. Anybody with one on theirs mind posting pics and a video of it running/idling?
Yes, I do realize that it will probably look the exact same as on the '15. So none of...
Hey guys,
My ac has just started crapping out with it only able to work for about 20 mins before it will not cool air or blow it hard at all. My horn also quit working about 8 months ago if that helps at all. Any help is greatly appreciated!
I bought this 2011 GT recently and it's turn signals are not actuating right. The previous owner did install LED switchbacks and I'm wondering if these have any thing to do with the problem. Anyway, so in short the tail lights do not light up sequentially when turning, braking, or when in...