Search results

Has anyone tried adding carseat latch tethers to a 94-98 car? Been wanting to try putting my 2.5 year old in the back for short drives but was hesitant since there were no latch tethers for his front facing carseat. I happened to be at the Junkyard getting some stuff for my xj and saw a bracket...

Anyone seen any good black Friday deals pop up on AMP research power running boards? Thinking I might pick up a set for my 15 super duty. The factory boards are starting to show some corrosion and we just can't have that. Looking at getting a set of the hard wired standard ones.

I remember seeing a thread on this way back when they first started the project but couldn't find it to post an update. They got this thing put together and fired up today. Sounds incredible, it's a shame Ford never produced them. Looking forward to see the rest of the project come together.

Who are the go to guys for remote tuning an MS3 pro setup these days? Thinking it might be time to have someone step in and fine tune what I have started. I have had my car running and driving on a MS3 pro ultimate for about 3 years now. It runs pretty good but I have everything dialed back to...

Does anyone know where to source this hose. It looks like ford discontinued the part number a while ago and I didn't see any aftermarket replacements on the usual sites. Doing some power steering maintenance and this hose is getting pretty hard after 27 years and ~180k miles.

Been mixing my own pre for years but my wife is tired of all the bags sitting on the counter. Not a hill I'm willing to die on so looking at alternatives. I had been mixing raw ingredients for the longest time, worked great and super cheap. Less than 50 cents/serving if I would shop around...

Anyone purchased a Timken front hub/wheel bearing assembly recently? I got this from amazon and it is suspiciously lacking any markings on the hub, is about 5 ounces lighter than what Timken has in their catalog and the bearing just feels off for being brand new. I submitted a claim to stop...

Does anyone know who/if there is still a contact at Gates for RPM belt length requests. My 114.5 I had them add to their list years ago is to short for my new setup. The last time I tried emailing Chad at [email protected] it bounced back as undeliverable so I assumed he was no longer there.

Looking for a Metco 3.0 alternator pulley. They are out of stock at the moment. I have a 3.2" I could trade if interested but it was modified to fit a 96-98 alternator, it could still be shimmed to fit. It was modified to fit a 96-98 alternator.

I pulled this off the car when I set the factory gauges to be driven by an MS3. This will allow you to convert your factory dummy oil pressure to a functional 0-100 psi gauge. It does take a bit of calibration but the step by step how to Mark Olson put together is very thorough. Write up is...

Does anyone have experience with running a newer starter from a coyote car on their 4.6 based motor. I am in need of a replacement and came across the ford racing M-11000-C50 which states it fits 96-19 manual cars and it quite a bit smaller/lighter. It looks to be identical to the Motorcraft...

Anyone know of just a blower motor cover replacement? Putting the dash back in the cover pretty much exploded trying to plug it back in. It's almost the consistency of a clay pigeon. Blower works fine so I'd rather not replace it if necessary.

Does anyone have the Verizon 5g home internet? I was just notified it was available in my area. $25/month vs the $90ish through charter seems to good to be true. I get 3-400 Mbps through 5g on my phone through Verizon currently which is ~4x faster than my current Charter internet.

Can anyone confirm that the factory tach signal from the factory ecu is a low amperage 12v pulse/square wave signal? Wanting to add the factory tach to the outputs from my ms3pro. It has a tach output that I believe should work but wanting to verify before cutting the wire going to the factory...

Looking for a parking brake boot for a 01-04 car. The boot can be junk I really only need the plastic ring that holds it to the center console. So the cheaper the better

Looking for a 94-98 dash clock. Doesn't need to be working, would prefer not working actually. I only need the housing, mine has a broken tab and I gutted the factory clock years ago. Would hate to trash a good working one

Does anyone have access to or know where to get a full 96 cobra wiring diagram that shows connector locations and their pinouts? Trying to run a sensor using left over stock wiring but need to make sure they go where I think they do. I have a Haynes manual and some printouts on the ecm wiring...

Has anyone successfully setup a low doller motorsports combo sensor in MS3. Their instruction specifically say not to use a “linear scaling” or “fill row value” for the setup but when I chart their values it looks pretty linear. I am using it for an oil pressure/temp sensor so if it is a few...

Does anyone know what type of muffler the borla catback for our cars uses? As in what borla product line? I believe it is a pro xs but haven't been able to verify. I currently have the catback and love the tone and volume but was looking into building a comparable 3" catback to match my 3" ARH...

Anyone in the Atlanta area have insight on the riots going on downtown? I am headed down there Sunday for a tradeshow and staying at Sheraton Atlanta Hotel downtown. Leaving Wednesday afternoon. Is it generally media hype? Is that hotel or the Georgia World Congress Center convention center in...

Anyone know of any deals on odyssey batteries for black Friday/ Cyber Monday? Mine died in the car a few weeks ago and looking to replace with a PC925LT/PC925L. Cheapest I've found is about $250 shipped.

Looking for 2 fog light buttons for a 01-04 mustang. Switch button condition does not matter as long as it works. The harness is not needed but plus if it's there. Edit: Got one still looking for another.

Anyone with decent power swapped from 17s to 18s. Highly considering picking up a set of the new LMR machined face 03 reps in 18s to replace my 17 machined setup. I am concerned about having to go from a 315 35 17 to a 305 35 18 and how that will adversely affect traction. If its going to be...

Anyone ever had to deal with getting a refund from apple? Booked way back in April for a 5 day in Cancun. Early part of June the outbound flight got canceled so I called and was told I would get a full refund since the flight was canceled not rescheduled. Called back every few weeks to check...

Anyone have issues with fuel temps and possible pump cavitation? A few weeks ago the car died and I had to push it to the side of the road and let it set for the afternoon. Luckily it was in my parent neighborhood right in front of someone's house. Ambient temp was 99° and the fuel temp got up...