2003 Torch Red Cobra 70,508miles as of 5/11/10
It made 589 whp on 18psi.
Shell V power 93 pump gas
I will try to find my dyno sheet & post it as well
Mods:
Engine:
Gen 2 Whipple 2.3 with factory 3.5 upper (approx 9k miles on it)
#6 lower with quick change setup
LFP billet idler...
Wanted:
99-04
1. driver side or pair of interior door handle/pocket/ bezel for coupe with power windows & mirrors.
2. Radio bezel for 6disk cd changer with air vents preferably that fits the 3 buttons in the bottom for fog lights, trac control, & rear defrost
I prefer black but will take...
I'm thinking about Selling my 03 Torch Red Cobra.
Its heavily modded in my opinion.
Car has 69k miles.
Mods
2.3 Gen 2 Whipple
Billetflow pullies
GT pumps in a Fore hat
-8 Fuel line from tank to engine.
75 lb RCI injectors
MAC long tube ceramic headers & Pro chamber
Flowmaster...
I bought sum 325/45/17 M&H DRs. approx 28" tall
I was told they would fit on my 10.5 rims which they do.
They are on my 03 cobra with a SRA conversion.
Is anyone else running these tires??
If so did you have to roll the fenders and/or use a spacer?
Well,
Me, Beau, & Allen went to Gearheads (Arlington, TX) today. Thing 2 got all tuned up ... Decided not to do the high boost at this time. Travis & I were kind of pressed for time.. They are definetly 200% more professional than HPP. They start work @ 9am. Told me to be there @ 9:30 & car...
I'm needing to get my hands on a set of factory fox a arms for a project. I'd like them to be in good condition with the studs to mount the tie rod end on if at all possible.
Pm me with any you may have.
Thanx :beer:
Magnaflow cat back kit. Not sure what part #. I bought used myself from an SVTP member & ran it for a year. I was very happy with it & the only reason I'm selling is because I went from an IRS to an SRA.
$250 Shipped
So I'm hopin with my new mods to make around 600 hp or so. I currently have a solid rear with double adjustable upper arms. heav duty lower arms. Tubular K member & Eibach drag springs.
I'm plannin on buying some 90/10 front struts & some 50/50 rear shocks.
Considering running the 315 et...
Hey guys I'm almost ready to tune my car. I just did a lot of work. I'm wondering if anyone has a similar setup. I don't want to get my hopes up too high but i'm hoping to make around 600whp. I'll be getting it tuned by HPP in Dallas, TX
Here's the mods.
Feel free to chime in with any...
Black Billetflow IRS Brace. Never installed!
Also a Steeda Bushing kit & Maximum Motorsports low profile bolt kit for mounting 10.5 wide wheels w/ 315 tires on factory irs.
Building a heavy duty solid rear & sold my factory IRS
Selling as a whole package
$175 shipped.
Hey SVTP I'm considering goin auto to relly get some great launches & ets at the track. I'm just not really great on the stick... I am wondering if a beefed up auto tranny with a convertor out of a mach 1 or GT will do the job... I'm not really wanting an overdrive gear & not go the c4 route...
Any SVTP members located in or around s'port/bossier???
I seem to see a heel of a lot of gm cars but not very many svt/ford cars.
It could be i'm not in the loop. I'd like to get involved & run my car against guys with similar car interests.
Wanting a fuel rails & injector setup... Good working condition. I don't want to get a set of 8 injectors that only 6 work if you know what I mean.
Let me know what you might have
Thanks
Like the ad says I'm looking for a set of subframe connectors & k memeber kit Complete with everything I need to install on my 03 cobra. If anyone has anything like that shoot me a message.
:beer:
Wanting a set of headers & mathcing midpipe to fit up to my cat back so I can finally have a full exhust system.
Shoot me some reasonable offers if you have anything.
:beer:
I have a 26 spline Ram twin disk setup for a 03-04 cobra T56. Approx 100 miles on it No signs of wear. I don't need it because I am not going to be makin 800+ HP and don't need the extra weight.
$850 shipped
PM me if u are interested
Thanks
A few months ago I bought some used dss levels 5 shafts from right here on svtp. Well when i got them the 1 rubber boots on each shaft is split open.. when i took off one boot.. all of the needle bearings fell out! :eek: so needless to say that was money down the drain... :fm:
However I am...
I posted this earlier, but i have made my decision.
I'm selling my Torch Red 03 cobra. I'm getting married & need to make some room for other things. It has a couple of chips in the paint on the hood & pass door.
Here's the run down. Please Read everything!
17x9 - 17x10.5 chrome cobra...
Hey everyone,
I live in Shreveport, LA & I am wonderin if there is a shop in the area where I can take my 03 cobra to have the IRS bushings replaced, IRS brace installed, halfshafts & gears installed. I would like to not have to make a 3hr drive to dallas if I can find a good performance shop...
Hey Guys I am a little curious on the details of mounting a 15in draglite rim on a IRS rearend.
Do I need spacers, or it it even possible?
I know I had to put the round allen head bolts in the rear to keep my 17x10.5s from rubbing the inside.
I am just trying to get sum aswers before I...
looking to do some serious upgrades.
i'm looking for a Whipple or KB & injectors to really get my cobra moving.
Also need a set of LTs & midpipe.
Also wanting a tubular k member & a arms.
anyone know someone looking to get rid of some of this stuff at a reasonable price hit me up.