2013/14 GT500 Engine and Transmission & Underhood Wiring Harness Drawings

Snoopy49

Well-Known Member
Established Member
Joined
Jun 12, 2012
Messages
6,675
Location
California
These are from the 2014 Ford Service Manual.

5.8 Engine Wiring Front View.jpg
5.8 Engine Wiring Rear View.jpg
2013 GT500 Transmission Wiring.jpg
Underhood Wiring.jpg
 
Last edited:

Tob

Salut!
Super Moderator
Joined
Mar 17, 2009
Messages
11,481
Location
The Ville
Interesting that the transmission shown is still using the fixed flange from the earlier GT500's when that clearly is not the case.
 

Snoopy49

Well-Known Member
Established Member
Joined
Jun 12, 2012
Messages
6,675
Location
California
Interesting that the transmission shown is still using the fixed flange from the earlier GT500's when that clearly is not the case.

I hope the wiring harness represents an accurate view. I have noticed this in several service manuals, Some one in tech pubs gets lazy and uses an earlier example. In this case they were trying to show the wiring in relation to the transmission and weren't bothered by a few discrepancies in the transmission. I bet that if you looked it up in the 2010 Service manual, you will find the same example.


Thanks for the title change. :)
 
Last edited:

Snoopy49

Well-Known Member
Established Member
Joined
Jun 12, 2012
Messages
6,675
Location
California
Image 3:
What is S139 and S140?
Tie downs?

S = Splice
C = Connector
The number after the letter indicates location.

S139 - Wiring harness - Starter motor relay and battery near T/O to C1572
S140 - Wiring harness - Starter motor relay and battery near T/O to C1571

C1571 - Universal Heated Oxygen Sensor (HO2S) #11 - On exhaust pipe, RH side, upstream
C1572 - Universal Heated Oxygen Sensor (HO2S) #21 - On exhaust pipe, LH side, upstream
 

Norton

Long-time SVT Enthusiast
Established Member
Joined
Dec 11, 2012
Messages
2,737
Location
Colorado Springs, CO
Informative and useful post, as always, Snoopy. Thanks!

Are you screenshotting this kind of stuff from the Helms electronic manual?
 

_Satch_

Active Member
Established Member
Joined
Dec 4, 2012
Messages
182
Location
PA
UnderhoodWiring_zps9c2394be.jpeg
58EngineWiringFrontView_zps5ac75120.jpeg
58EngineWiringRearView_zps0dcca970.jpeg
2013-14 GT500 CAC Wiring Diagram.jpg
2013GT500TransmissionWiring_zps87d2c4bf.jpeg
BATTERY JUNCTION BOX CAC.jpg
Connector C1217 - CAC Pump.jpg
58EngineWiringFrontView_zps5ac75120.jpeg
58EngineWiringRearView_zps0dcca970.jpeg
I'm not sure if these are the original images that were in this thread, but I've snagged most of the stuff Snoopy49 has posted for a couple of years. Thanks Snoopy49!
-Satch
58EngineWiringFrontView_zps5ac75120.jpeg
58EngineWiringRearView_zps0dcca970.jpeg
 

Attachments

  • Fuel Pump Schematic 2013-14 GT500.pdf
    355 KB · Views: 182

Snoopy49

Well-Known Member
Established Member
Joined
Jun 12, 2012
Messages
6,675
Location
California
I'm not sure if these are the original images that were in this thread, but I've snagged most of the stuff Snoopy49 has posted for a couple of years. Thanks Snoopy49!
-Satch

Thanks for posting the pictures.
Thanks to SVTPerformance.com, I was able to edit my original posts and restore the pictures. Being able to edit older posts that are affected by the PhotoBucket problem is a real asset to the community.
 

_Satch_

Active Member
Established Member
Joined
Dec 4, 2012
Messages
182
Location
PA
Thanks for posting the pictures.
Thanks to SVTPerformance.com, I was able to edit my original posts and restore the pictures. Being able to edit older posts that are affected by the PhotoBucket problem is a real asset to the community.

No problem Snoopy49... Thank You! I snagged most of the .pdf stuff you posted in the past too, the supercharger cooler plumbing spec was especially helpful when I swapped over to the VMP triple pass heat exchanger this past weekend.
-Satch
 

Norton

Long-time SVT Enthusiast
Established Member
Joined
Dec 11, 2012
Messages
2,737
Location
Colorado Springs, CO
I'm not sure if these are the original images that were in this thread, but I've snagged most of the stuff Snoopy49 has posted for a couple of years. Thanks Snoopy49!
+1. Having Snoopy49 as a member of the community negates the need for a technical library.
 

Users who are viewing this thread



Top