F/s: Whipple 2.3l sct lfp

[NITROS COBRA]

Used 2.3l whipple black under 2,500 miles, like new 3.5 pulley, like new 3.0 pulley, used sct ba 2400 maf, new diablo mafia, used kenne bell 40 amp bap, new 6 lbs lower lfp crank kit with 3.5 inch alt pulley. Make me an reasonable offer. Would like to sell as set.

 

[slowfokes]

got any pics?? email [email protected]

 

[countrysvt]

how much, how bout some pics?

thanks

 

[Jerry03cobra]

Picture please [email protected] how much boost were you running?

 

[NITROS COBRA]

I was running 16 psi, 596 rwhp and 522 rwtq. 16 timing, pump gas

 

[NITROS COBRA]

Whipple 2.3l
60 lbs injectors
kenne bell bap
ba-2400
reichard pulley 3.1 pulley
lfp lower 6 lbs
lfp alt pulley 3.5 inch
whipple 3.0 pulley
DIABLO MAFIA

i would like to try to sell as a kit, tons of parts. Give me a list of what you need and your offer?
NO MORE THAT 2,500 MILES ON THESE PARTS

 

[image]

Looks like its worth about $4200 bucks.

 

[Jerry03cobra]

How much for.Whipple 2.3l
60 lbs injectors
ba-2400
reichard pulley 3.1 pulley
whipple 3.0 pulley
DIABLO MAFIA

Is the valley in texas?Send me a pm on the price thanks

 

[Posi]

Looks like its worth about $4200 bucks.

Talk about a complete Twin Screw setup. This should make someone's decision pretty easy buying it all at once.

 

[slowfokes]

is it sold? and are you located in texas?

 

[NITROS COBRA]

Located in california. Not sold. Check your pm, left phone number

 

[breoland]

sent you an email a few hours ago and didnt hear back

 

[NITROS COBRA]

This is a rough break down
whipple 2.3l $2,500 retail a toulsey $2,900 before price increase.
Mafia $125 retail $175
bap $150 retail $275
6 lbs lower & alt $300 retail $375
60 lbs inject $250 retail $375
3.1 reichard $75 retail $150
3.0 whipple $60 retail $130
ba-2400 $115 retail $230

so i would like to get $3,600 for all stuff plus shipping. Retail would be $4,635, so a savings of around a grand.

 

[NITROS COBRA]

I will mix and match parts to help the buyer, i do have more stuff too, just ask.

 

[Mach1man!]

Very interested...What would be needed to install this on a Mach 1, ...if so what else would i need to get...dont think i could get this set up any where cheaper? email me pics to [email protected].

 

[NITROS COBRA]

Mack1man
pulley bridge
balancer
timing cover
lower pulley set up
lower manifold
intercooler
pump
ic lines
the sad thing i just sold all this stuff, i might have another kit though

 

[NITROS COBRA]

Any interest??????????

 

[breoland]

you have a pm

 

[NITROS COBRA]

I will offer free install of all parts above. I will tune car for $400. You supply the x-cal 2 and accufab tb.

 

[NITROS COBRA]

REVISED parts list:

Whipple 2.3l black
60 lbs injectors, seiman deka
kenne bell bap, 40 amp
ba-2400
reichard pulley 3.1 pulley
lfp lower 6 lbs
lfp alt pulley 3.5 inch
whipple 3.0 pulley
diablo mafia
accufab throttle body
mac filter and adapter
fuel upgrade: aeromotive, 3/8 steel braided line, fuel tank fitting, fuel rail fitting, aeromotive filter, misc fitting to install.