Search results

OK so I'm at a loss here. Long story short, I had the DSS Level II axles and they worked great with no issues or noises. I picked up a set of used DSS Pro-Level axles (4,000 miles supposedly) with the upgraded hubs. I had the wheel bearings replaced when the hubs were switched. Put everything...

Hello everyone, I have up for grabs a pair of 03-04 Cobra Rear IRS Hubs with Moroso Extended Wheel Studs (cut down 1.10"). Only reason for sale is because I went with the Pro-Level axles that come with the upgraded hubs/studs. They are located in Sterling Heights, MI (48313). $100...

Hey everyone, I have up for grabs the chin spoiler off my 03 Cobra. Long story short, I tried refinishing it myself. I had sanded and prepped it nicely so all scuffs and scrapes were removed. I tried using Plasti-Dip for the finishing product (first time every using the stuff) but I made two...

Hello everyone, I have a pair of Eibach Coil-Over Springs that came with my UPR Coil-Over kit. They are a 12" spring with a 175 spring rate. They were ran on my 03 Cobra for about 3,200 miles. They were removed to try running a different spring rate...

Hello everyone, I have a pair of Eibach Coil-Over Springs that came with my UPR Coil-Over kit. They are a 12" spring with a 175 spring rate. They were ran on my 03 Cobra for about 3,200 miles. They were removed to try running a different spring rate...

Hello everyone, I have a pair of Eibach Coil-Over Springs that came with my UPR Coil-Over kit. They are a 12" spring with a 175 spring rate. They were ran on my 03 Cobra for about 3,200 miles. They were removed to try running a different spring rate...

Hey Guys. I have the following for sale off my 03 Cobra. I'm taking REASONABLE OFFERS on all items. Please contact me via PM. I have pictures available upon request. - 2003-2004 Cobra OEM T-56 Transmission w/ Lethal Performance TOB Sleeve, OEM-Style Clutch and OEM Aluminum Driveshaft...

Hey everyone, thanks for looking! Since I'm not very active on this site, please send me a PM if interested in any of the items (that way I get an e-mail notification and can respond quickly). I'm taking REASONABLE offers on all the items listed and will ship. The only items I'm not willing to...

Hey everyone, I just installed a UPR Chrome Moly K-Member in my 03 Cobra. I got it on the ground today and noticed my driver wheel is not in its OEM location. It seems as if it has shifted towards the rear of the car. The wheel rubs the fender liner if turned to the left. However, the...

I have a Kenne Bell 40 Amp Boost A Pump up for grabs. Please PM for more details and a pic. $150 shipped Thanks for looking!

Just curious if anyone has any take-off OEM rear outer tie rod ends for the 03-04 Cobra IRS. I was unable to re-use mine after removing them out of the spindle. Please PM me if you have any with a price shipped. Thanks for your time!

Hey everyone, I'm sure this question has been asked before and bare with me, I don't come on the forums often... I'm aware of where I can purchase all the aftermarket half shafts for the 03-04 Cobra, but where can I get either new OEM or remanufactured 03-04 Cobra half shafts? If there's a...

I have up for grabs an 03-04 Cobra UPR Cold Air Intake (black) off my 03 Cobra. See the link for the product. The kit is in great condition and includes all hardware. The filter is a little dirty, it could use a cleaning or if you really wanted to replace it with a K&N that'd work too. UPR...

I have a NEW Kenne Bell 3.25" 8-Rib Pulley up for grabs. It is made to take the new 12mm mounting bolt and has the short inner hub. Should fit all the new-style Kenne Bell's (to my knowledge). Please confirm it'll work with your setup before committing. New from Kenne Bell these pulley's are...

I have the following off my 03 Cobra for sale. Everything functioned as it should when removed. Just looking to clear some space out of the basement. The best way to contact me is text @ 586-203-7758. I work long hours during the week so I RARELY check SVTP. I also have pictures of everything...

I have a few things up for grabs off my 03 Cobra. I have pictures available on my phone so feel free to PM me with a phone number or e-mail address to send the pictures to. * Stock 03-04 Cobra 39 LB/HR Injectors * Stock 03-04 Cobra Heat Exchanger Assembly (Includes hoses and tubes that...

Up for grabs is a NEW Kenne Bell 3.25" 8-Rib Pulley. It is made to take the new 12mm mounting bolt and has the short inner hub. Should fit all the new-style Kenne Bell's (to my knowledge, I could be wrong though). It came with my first Gen 2.2L that takes the old 10mm mounting bolt. Since it...

This is just a feeler thread for a pair of polished Bassani Mufflers out of a Bassani Cat-Back off my 03 Cobra. They sound great, just looking for a different sound. The car is low so there are scuffs from the occasional scrape over some bumps, but no catostrophic dents! The mufflers are...

Hey everyone. I have a Stiegemeier Stage IV Ported Eaton up for grabs off my 03 Cobra. The supercharger comes pullied with a Billetflow 2.76" Upper Pulley, as well as the Accufab Ported Inlet Elbow from the throttle body to the supercharger. The blower also comes with the inlet elbow hardware...

Hey everyone, I'm on the market for an 03-04 Cobra currently. Not picky on a color. Milage preferred under 60k. I'm located in the Metro Detroit-area but am willing to travel for the right car. Looking to currently spend $18k or less. Call 586-203-7758 (call after 4:30p, text anytime) with what...

Hey everyone I'm looking for a 2.2L Kenne Bell Supercharger kit for an 03-04 Cobra. I know they don't make these blower kits anymore and they'll be hard to find but I figured I'd test the waters and see what's out there. E-mail [email protected] if you have anything up for grabs. Cash in hand!