terminator

ATTENTION COBROS! This one is for you! $1250 SHIPPED on our Cobra Crank Support Kit. This is a MUST HAVE on any high powered 2003-2004 Terminator Cobra! This is the Lethal Performance Cobra Crank Support System. It is designed to take shear/flexing forces off of the crank snout known to damage...

ATTENTION COBROS! This one is for you! $1250 SHIPPED on our Cobra Crank Support Kit. This is a MUST HAVE on any high powered 2003-2004 Terminator Cobra! This is the Lethal Performance Cobra Crank Support System. It is designed to take shear/flexing forces off of the crank snout known to damage...

ATTENTION COBROS! This one is for you! $1250 SHIPPED on our Cobra Crank Support Kit. This is a MUST HAVE on any high powered 2003-2004 Terminator Cobra! This is the Lethal Performance Cobra Crank Support System. It is designed to take shear/flexing forces off of the crank snout known to damage...

If you know CoBro, you also know it's been a long time coming for this project! Today, it can finally be said the build is done!! In the most recent video, Jared goes over the entire Cobro Build from when he first got the car, all the way until today! Mentioning all the great partnerships that...

If you know CoBro, you also know it's been a long time coming for this project! Today, it can finally be said the build is done!! In the most recent video, Jared goes over the entire Cobro Build from when he first got the car, all the way until today! Mentioning all the great partnerships that...

2003 Sonic Blue Cobra Coupe 48k Miles Clean title Rust Free Garage Kept Carfax in hand $45k $40k on stock wheels without CCWs Exterior: 9/10 Polished and Coated with CSL and Exo v4 08/21 Interior: 9.5/10 normal driver bolster wear Washed the car with a foam cannon and 3 bucket wash...

Thinking of parting ways with my '03 cobra. im still unsure if i want to sell the car, however I have my eyes on another car i want. Car has always been reliable, smooth and lots of fun. 67xxx mile car. Simple setup, just a 2.3L whipple with 3.0inch upper pulley/stock lower. (~16lbs boost) ARH...

Finally! On the way to us, and should be here in just a few days! The Lethal Performance Crank Support for your terminator cobra. What's a Crank Support designed for? This is the Lethal Performance Cobra Crank Support System. It is designed to take shear/flexing forces off of the crank snout...

UPDATED Still need the below: Need a few things for my 03. I'm ready to buy: Engine Wiring Harness - can be with ECU or without Factory Injectors or slightly bigger (All 8 for stock motor) Factory Boost Bypass Valve Factory Eaton Pulley Alternator (higher output preferred) Throttle Body...

Price is $5,000 for the lot: Everything is brand new in box, ordered around December of 2020. Have a few parts I ordered but decided against installing on my Cobra. Selling as a single lot and local pickup preferred due to size/amount of parts, parts are located just north of Chicago. I have...

Clean title car with under 46k miles. Tastefully modified. Specifics obtained from previous owner who built it are in the photos. Motor was built by Edison’s one off Customs at 38,000 miles or so, per previous owner. It has a race honed teksid block, stage 3 cams, new upgraded King bearings...

WTB: ISO 03 Cobra Hood Insulation I know this is prolly a long shot, but my hood insulation is in dire need of replacement and have not found any reasonably priced used ones for sale. Txt me four 4 three, nine 6 seven, three five 3 three.

Clean title car with under 46k miles. Tastefully modified. Specifics obtained from previous owner who built it are in the photos. It has a teksid block, stage 3 cams, KB 2.8LC mammoth. Motor has like 7k on it. 26 spline input shaft, 8.8 SRA with 31 spline axles and 4.10 gears. Subframe...

2003 mustang cobra sonic blue 93k original miles Unmolested vehicle 95% original car. Borla mufflers Jlt CAI High output alternator (180amps) Everything else stock New spark plugs(TR6ix) New fuel filter Fresh oil change Los Angeles, Ca 90606 30k obo

My first post, if I'm in the wrong section it'd just because I'm burned out from researching this stroker kit. I have an 01 cobra 90k, I took a teksid 98 mark viii block, found a used Manley true 5.0/305/9.08cr rotating assembly on eBay. Had a local machine shop bore and hone it .20 over as well...

Hello, I am looking for a cobra supercharger lower manifold. Part # 2R3V-9J447-BB preferably not ported if you have one that is clean and in good condition, please contact me

**** HAS NO OVERDRIVE IN TRANS BEFORE YOU READ IF THAT SCARES YOU AWAY**** Its a 2004 Redfire Cobra Coupe with a little over 64,000 miles on the body. It makes north of 850WHP (probably a little more haven't had on dyno) and runs 9's at the track at 147ish mph. Everything on the vehicle is...

Finally back in stock... 26 spline input shafts! A must for a clutch swap!!! Let's build you a clutch kit combo! If you have any questions or do not see exactly what you are looking please contact us at 561-753-8105 or send us a message ! Link to our product - Lethal Performance LP-TUFM6132K...

Finally back in stock... 26 spline input shafts! A must for a clutch swap!!! Let's build you a clutch kit combo! If you have any questions or do not see exactly what you are looking please contact us at 561-753-8105 or send us a message ! Link to our product - Lethal Performance LP-TUFM6132K...

Finally back in stock... 26 spline input shafts! A must for a clutch swap!!! Let's build you a clutch kit combo! If you have any questions or do not see exactly what you are looking please contact us at 561-753-8105 or send us a message ! Direct link to product - Lethal Performance LP-TUFM6132K...

SOLD -- Two USED Terminator wheels off my 03 Cobra. $100 each + Shipping from Minnesota. PM if interested. First 3 photos are Wheel #1 Last 4 photos are Wheel #2 Wheels are solid, no damage whatsoever, cosmetics are very good. PM if interested, Thanks! Warrlac

Sorry if this is a redundant post. Does anybody know where to get a performance power steering pump for the 03-04 Cobra's other than MMR? I came across the thread at the URL below earlier this year when I was researching a replacement, but of course they don't have any in stock now that I'm...

USED Reichard Racing Ultragrip 2.95 inch SC Pulley for Eaton. $75 + shipping. Located in Minnesota.

SOLD -- New 90mm, 4-Pulley Set includes billet belt wrap auxiliary mount. (was $170 + shipping) NEW PRICE = $120 + Shipping. Located in Minnesota.

Located in NY but willing to travel for the right car Max budget of 50k Cash in had for the right car Any leads are Appreciated or help!