I'll keep them on my list.
I, along with a few coworkers, have been going to CarGuy in Chandler. They installed my VMP Gen II, and suspension work for my coworker.
Gene, the owner, also does engine builds for FoxBody Performance up in Peoria.
My VMP GEN2 STG2 install on a 2014 GT auto
- Thread starter Zona14Stang
- Start date
I'll keep them on my list.
I, along with a few coworkers, have been going to CarGuy in Chandler. They installed my VMP Gen II, and suspension work for my coworker.
Gene, the owner, also does engine builds for FoxBody Performance up in Peoria.
JPC E85 Kit on the way! Install pictures to follow 
Just ordered the MMR OPG, MMR Timing Gear sprocket, and ATI Balancer. Now I am done!
lol the fun never stops...
Lethal Performance got it through VMP with a tune update. You need the tune update since you are deleting the Cats
Yea that's the one I am gunning as well..
It's the stainless steel one?
Do you feel any difference other than the sound?
Thanks
I did not get the stainless steel one, It sounds awesome not really sure if you can really feel the diff but you can hear the difference.
lethal Hpipe pics
Installed the fuel pumps yesterday.
It took alot of torque to break the damn thing free. I could not image not using the tool. Unfortunately you have to make a small cut to get the damn ring out. Not the brightest design by FORD. I bought the tool on Amazon it is worth it.
Also make sure to vacuum all the crap out from the top so it does not fall in the tank.
It took alot of torque to break the damn thing free. I could not image not using the tool. Unfortunately you have to make a small cut to get the damn ring out. Not the brightest design by FORD. I bought the tool on Amazon it is worth it.
Also make sure to vacuum all the crap out from the top so it does not fall in the tank.
Last edited:
more pictures
more pics
Had to use a pipe on the 14" breaker bar to tighten it back down
Thanks again to Sam for answering my questions yesterday.
Tommorrow the fuel lines and relay box and wiring.
Had to use a pipe on the 14" breaker bar to tighten it back down
Thanks again to Sam for answering my questions yesterday.
Tommorrow the fuel lines and relay box and wiring.
Last edited:
Today's pictures not a lot done today tomorrow will do the fuel lines.
Mounted the relay box in the trunk and ran the 4 gauge power wire. Kind of a pain but I had done that already for my amplifier wire you have to remove the interior pieces on the passenger side jack up the car and remove or loosen the passenger wheel well liner the expose the rubber grommet to run the power wire through.
Mounted the fuse block on the firewall near the battery.
Mounted the relay box in the trunk and ran the 4 gauge power wire. Kind of a pain but I had done that already for my amplifier wire you have to remove the interior pieces on the passenger side jack up the car and remove or loosen the passenger wheel well liner the expose the rubber grommet to run the power wire through.
Mounted the fuse block on the firewall near the battery.
Last edited:
Thannks
Still working on the fuel system what a PITA running the fuel lines. More pictures coming tomorrow. Trying to get the damn old fuel line out by the gas tank.
Still working on the fuel system what a PITA running the fuel lines. More pictures coming tomorrow. Trying to get the damn old fuel line out by the gas tank.
more starting to install fuel lines
have to loosen K member to get plastic out.
there is a clip up by the tank you have to put a screwdriver in there to loosen it to get the fuel line out by the tank
there is a clip up by the tank you have to put a screwdriver in there to loosen it to get the fuel line out by the tank
line from by the tank
wiring in the relays
fuel pumps and wiring from back seat
wiring in the relays
fuel pumps and wiring from back seat
Last edited:
Finally had time to work on it again
more pics
I put in a fuel cut off switch just the ground from the relays to the switch to ground
old and new fuel lines to show the size difference
I put in a fuel cut off switch just the ground from the relays to the switch to ground
old and new fuel lines to show the size difference
Users who are viewing this thread
