Pics of my car with CCW

[homel01]

Finally this are the pics of my car
It has FRRP suspension
lower bmr control arms with relocation brackets
Afco Heat exchanger
JLT intake
NGK t6 Sparks
Magnaflow 3' exhaust and custom 3 h pipe
2.6 upper pulley
lower pulley
Kenne Bell Dual Boost a Pump
PFAB bigger reservoir
McLeod dual disc clutch and Fidanza flywheel 1200 whp capacity
CCW wheels 19 x9.5 and 19 x 11
BFG KDW tires 275/35/19 and 295/35/19
Steeda brake upgrade slotted + stainless lines, 14' Front and 13' upgrade rear
currently 558 whp and 596 tq waiting for NEW EVOPERFORMANCE TUNE :burn:

 

[Willie2]

looks good!

 

[no one]

very nice setup.

 

[SVT03Chris]

Awesome numbers! Car looks sick!

 

[Bravo gt 500]

I like the look, but i think it will look better with black stripes or no sripes imo.

 

[homel01]

I like the look, but i think it will look better with black stripes or no sripes imo.

Yes this will be done, but i don't want cheap quality stripes and good ones are like 400+$ so this will be done in time. as can be seen on the pics, I remove the side stripes

 

[skyhighsd]

Looks good, but I would have went with the polished wheels instead but thats JMO

 

[Willie2]

what lower pulley are you running? or are you talking about the idler?

 

[davidhuff]

Shelby looks great and thanks for the pictures!

 

[GOTSVT?]

How much were the rims?

 

[homel01]

what lower pulley are you running? or are you talking about the idler?

I use the 2.6 upper and metco idler

Lower is Innovators 4psi +

Boost peak in my car is 17 psi

 

[homel01]

How much were the rims?

3500 without tire sensors

 

[homel01]

I forgot to put this pics on

Nexus Gauges:
Boost
Wideband

with autometer carbon fiber cups

 

[Graves]

Nice!

 

[rdsnk46]

I like the wheels!!!! Black stripes instead of white, any reason you didn't get a pilar speed of sound gauge pod? I like the CF cups but the mounting hard ware is out dated and looks out of place to me. That's my opinion though and you know what they say about opinions......... it's your car! Enjoy!

 

[KILRSVT]

looks nasty.....:rockon:

 

[09Troublemaker]

nice job. just 2 hmmms

1) why only 295's on that 11" wheel, offset?

2) Does your A-M wideband run the bosch 02 sensor?

Man if you ran the "no stripe" I think you would be hotter then
lighting, IMO

 

[homel01]

nice job. just 2 hmmms

1) why only 295's on that 11" wheel, offset?

2) Does your A-M wideband run the bosch 02 sensor?

Man if you ran the "no stripe" I think you would be hotter then
lighting, IMO

1) tire sizes are a headache, i could have gone wider but 305, 315, are 30mm or 25mm and thats too low for me, and if it was not that then i had to go 265 up front. Most brands jump from 295 to 345 and that doesn't help me either.
I wanted to keep front and rear as closest as posible. 255 front and 315 rear won't be good on turns

2) yes that was the sensor included withe the gauge
3) before ordering the stripes I'll remove the white ones and drive it a while to see if I like it that way

 

[R1Lello]

As I once wrote in the past, black rims are nice (well some of them ) but too bad they take the 'pop' out of it.........so now you don't know they are $3000 rims or $200.

 

[Dave07997S]

SWEETT!! You nailed the tire selection. That car looks ready to tackle Laguna Seca..:beer:

Dave