TVS 2.3 Dyno numbers please post

[The Beast 2014]

I know I am the reject on the forum with the only Edelbrock lol but still. Figured I would contribute. Mods are in my signature but on a Mustang Dyno with a 3.25 inch pulley (82.55mm) and 6.5 pounds of boost on 91 octane I am putting down 575. Going to pulley down to a 3 inch soon with e85 and hoping to put down about 680 with 10 pounds of boost.

 

[dsmith658]

730.63 rwhp 609.67 rwtq (Dynojet)

Aluminator 11:1
Roush TVS - 69mm Pulley
VMP Elbow / 67mm Twin Jet TB
E85
JLT 123mm Intake
ID1000s
Stainless Works 1-7/8" Catless X / Long Tubes
Borla Over Axle Pipes
GT500 Mufflers

 

[corepwn]

800rwhp~ auto.

Aluminator 11
VMP Gen2 w/SnakeBite. 75mm upper pulley and stock lower.
VMP Twin 67mm TB
JLT 123mm
E85, JPC Fuel System (2x 465s), ID1300s
Stock manifolds, Lethal OR-H, Stock OTA, GT500 Mufflers

Adding Kooks LTs now and possibly drop to a 69mm pulley to see what happens.

 

[DaBigBone]

Stage 2 VMP TVS, 82mm w/ 47lb Injectors + BAP, JLT CAI, Dual 60mm TB, Offroad X-Pipe....I made 564/496 on a Dynojet on my 3rd run. First two runs were less as the tech said my clutch was slipping a bit since it wasn't warmed up yet, engine didn't have much chance to cool down though. between the runs. I'm seeing around 9-9.5 peak PSI here in Ohio.

I really would like to hit mid 600's and call it a day, so I recently switched over to E85 w/ ID1000's. Car definitely runs smoother on the corn but I haven't noticed much different in power, I'll be following up with some logs for Justin to see how it's looking soon.

Figured you'd be a little higher than 560 with an 82mm and offroad x. Auto?

 

[tones_RS3]

Alex12GT had a pretty slick setup on his old ride... this was his setup>>>736rwhp, 688rwtq with the Roushcharger, 72mm pulley, id1000's, JLT Coldair intake, Vortech BAP, and Pypes Headers on an Aluminator engine w/ Billet oil pump gears... that was on 93 pump gas

WOW, I would love those numbers. That's some serious power and torque. All on pump gas too.
What tune was this car using? Obviously I wouldn't push it with my current Roush Stage 3, but I've been thinking of "building" a S550 GT PP. We'll see.
Thanks!

 

[Scott8583]

850 whp ported VMP Gen 2 on Corn
17 psi
Stock cams
BBK 1 3/4 long tubes
6r80 auto

 

[sambandit]

 

[bohica281]

Looking at a used 13 A6 with the roush 540 kit but skittish on pulling the trigger if it's a ticking time bomb, what rwhp should it be making?

Don't be skittish, I bought a 14 GT/CS A with a stage 1 Roushcharger already installed on it 1 1/2 years ago. With the stock Roush tune it is very safe. Did some mods and a tune from Justin. Trapping 135-136 mph in 1/4

 

[CompOrangeCobra]

Don't be skittish, I bought a 14 GT/CS A with a stage 1 Roushcharger already installed on it 1 1/2 years ago. With the stock Roush tune it is very safe. Did some mods and a tune from Justin. Trapping 135-136 mph in 1/4

Very nice, reading all these insane power numbers I'm feeling a lot better about pulling the trigger and joining you guys, sorry for the hijack OP.

 

[freemanjc]

VMP Stage II Kit, 85MM Pulley, 587 Power/505 Torque on a M6 and awesome Mike Rousch Tune!

 

[Potro-5XR]

Mine put down 548/460 with the phase 2 kit (625hp) stock roush exhaust and stock headers.