Recent content by dart454twinturb

03/04 cobra iron block 03/04 cobra forged crank Manley Billet I Beam Rods Forged Diamond Pistons 10.5:1 comp Total Seal AP Stainless Rings ARP Main studs ARP rod bolts ARP side block bolts Cometic MLS head gaskets MMR 7 qt oil pan MMR windage tray with gasket MMR pickup...

I have a th400 setup for sale. Was built and had 2 passes on it. Here is what all I have Neil chance built 1500 hp th400 with deep sump aluminum pan that has been tapped for trans temp sensor, and trans brake Lokar dipstick Modified t56 crossmember and rubber mount for the th400 Sfi...

I have the complete Mach 1 shaker setup for sale. Will include all brackets, bolts, drain hoses, cold air scoop, and hood. Also have a brand new hood decal to go with it. All parts are in excellent shape! I also have the engine and trans for sale as well. Message here or text me 785-608-9228

I am looking to buy a DSG 03-04 cobra decklid setup with spoiler and brake light. Doesn't matter if light is broken or not. PM or reply here. Paypal ready now. I can pick up within a reasonable distance or will need it shipped to 66605 Topeka ks. Thanks

I am looking to buy a DSG 03-04 cobra decklid setup with spoiler and brake light. Doesn't matter if light is broken or not. PM or reply here. Paypal ready now. I can pick up within a reasonable distance or will need it shipped to 66605 Topeka ks. Thanks

I have for sale a pcm out of a 2003 cobra. It is in good working order. Took it out to run a fast system. I also have a T56 wiring harness for the same vehicle. asking 225 shipped for the pcm and 115 shipped for the trans harness. YOu can message me here or text me at 785-608-9228.

Up for sale is a Joe van overbeek lift off cowl hood. I have Zeus rails to go with it. Have over 900 in receipts. Sell for 650 picked up in Topeka ks. Also have a 17" racecraft drag wing. It was mounted but I'm going a different route. 475 picked up in Topeka ks. You can message me here or text...

I have a couple harnesses for sale. One is the oem dash harness in great shape and one is the engine harness. Both in great shape. Can text pics. You can send me a pm but texting would be the fastest way to get ahold of me. 785-608-9228

Up for sale is a completely fresh built rear end. It started as a stock 99 gt housing. Had the quad shock mounts cut off and the tubes welded to the diff, has 35 spline moser axles, full spool, 3.90 gears, moser differential cover with cap studs, c clip eliminators, brand new cross drilled cobra...

Brand new QA1 175lb coilovers 94-04 still in the boxes 600.00 shipped Maximum motorsports caster camber plates 125.00 shipped Kenny brown extreme matrix subframe x brace system 400.00 picked up 425 shipped. Maximum motorsports 6pt bolt in cage with swing out door bars 600.00 picked up...

Shooting for around 1100 hp at the rear wheels. What have you guys done to reinforce this area. I was looking at a kit from wild rides race parts. They completely replace the factory ones with thicker sheet metal ones. Here is a pic. What else would you guys recommend??

Building my motor now. What head gaskets do you guys reccomend? Going twin turbo with around 18-24lbs and gonna be shooting for 1000 hp. What head gaskets should I use. Thanks in advance.

Up for sale I have several parts for sale. I will put prices on all that will include shipping. I would prefer not to ship the bigger items so local pickup in Topeka ks would be preferred. I will ship at buyers expense on those items though. I can provide pics of anything through text so feel...

I am looking for a built set of cobra heads. Ported and polished, upgraded valves, springs, retainers, hardened seats, and possibly turbo cams. Let me know what you got. PM or text 785-608-9228

Who has an aftermarket steering wheel in their car with a quick release hub? How did you do it. Any bolt in kits out there available? Lets see some pics of your setup and what parts did you use to do it?