belt

After months of weekends of tearing apart the car, rebuilding the Eaton snout, and upgrading the electrical system I’m finally where I can start the car and burp the cooling systems. While burping the systems I noticed that the supercharger belt is not aligned. The pulley on the alternator...

So I'm hoping that you guys might be able to help. I have a Race Posi Port Eaton with a 2.73 upper and 4# lower. I believe that the previous owner changed the alternator at one point and it looks as if the pulley is just the one that came on it from whichever parts store it was bought from. I'm...

I own a 2004 Terminator that I bought in 2009 after I returned from Iraq. It has sat in storage since 2010, as I was in Japan for the past 3 years. Now i'm taking it out of storage and need to repair it. Here is my issue: it's got a Whipple supercharger pushing 19lbs of boost and a metco...

Ok I have an issue I need help solving, all guys with 2.9L/3.4L whipples feel free to chime in. My car was in the process of getting tuned and has massive belt slip after 5300-5400 rpm. car noses off from 26.5psi at 5400 to 14psi. (Made 690whp at that point, so much more to be had :banana:)...

Hey guys so recently one of my belts (i believe) on my 03 cobra has begun to make a squeeking noise for about 5-10 minutes until warm. It then seems to go away completely. I was planning on replacing the belt soon, and was fine with this 5-10 minute squeek in the interim. However, today on my...

this very well may be a very stupid question... but w/ my vortech unit and the different pulley combinations where can i find a quick reference on what size belt to use? i'm going to push about 16lbs, but am on the stock 6 rib... any good places to find an 8 rib set up? or have you not had that...

I was wondering if anyone has a belt diagram for an 01 mustang gt procharged with no ac. Any help will be greatly appreciated thanks

stock eaton 2.93 upper 4lb lower (3) 100mm (1) 92mm billetflow idlers billetflow old style snub tensioner Belt is a dayco, 5080810, 367 What length belt do i have/need with my current setup? if i go to a 2.8 upper, what size belt would i need? Is a steel upper pulley better than...

my gatorback finally came in, so i installed it this morning. Got it on, started it up (with no squeaking!!), and noticed the belt was off the bottom pulley by one rib. shut it off, re aligned the belt. bumped the starter a few times and it stayed in place. started the car again, and...

right now i have a 79.5" gates belt on my car but squeaks due to being a little too large, and a tad glazed. closest i can find in gatorback is 79" and 79.7". I'm pretty sure i can get a 79" on there since i got the 79.5 back on quite easily with no help. I cant find the 79" gatorback...

I just got my first 03 Cobra a few months ago and my belt is a bit freyed, so now the big question "what size belt?" If all else fails I can take it off to measure, but trying to get one before I have to go through that. I went to CobraBob's site and I think I can figure out the size I need...

I have one Steeda blower pulley, 2.81 inch, and belt, both brand new still in the packaging. These parts are at a HUGE discount! Steeda Part # 555-3328 Belt Part # K080740 I only have ONE of these, so grab it while I have it. PM me if interested.

cog system for 03-04 cobra with a whipple just missing a tensioner pulley which is 200 from aspracing.com and they could make up a blower pulley as well for 200 if you had the stock supercharger still 1400 dollar kit, used, going another route with my car possible TT, looking for 700 obo