throttle body

I am selling a brand new VMP 137 monoblade throttle body. The TB has been never installed as I was acquiring parts in the late summer and early fall for my build. Those build plans have changed significantly, so now I am selling brand new parts. Works with 2015 - 2017 Mustang and F-150 (5.0L)...

#SOLD# Not shown, but includes gasket. Very nice condition, paint is dead match to Eaton. $85 + paypal + shipping

Hey guys, I just bought a used bbk 65mm throttle body from someone on this forum. It came off of his 2010 GT500 and he said the electronics part of it functioned perfectly. Would I be able to go ahead and just bolt it onto my 2011 without messing with the electronics part of it? Thanks!

SOLD

Hi all, I am selling my used BBK 65MM throttle body and my ported stock inlet elbow both from my 2010 GT500 still running the stock M122 Eaton. The BBK TB does come complete with the FoMoCo electronics, I believe these come "bare" without the electronics when new. I am asking $250 for the...

Hi all, I am a bit torn here and haven't found good information on this exact topic yet. I've got a 2010 GT500 with a Stiegemeier ported M122 with a 2.2" pulley, JLT 123 intake, BBK 65 MM throttle body, and VMP inlet elbow. I plan on adding the 13/14 56# injectors and VMP fuel pump boosters...

I have run into a problem with my 2010 GT500. I daily drive this car and have never had a problem with it but the other day I was driving at 2400 rpms and when I let off the gas, the rpms stayed at 2400. I pushed the clutch in, they did not drop. I had to turn the car off and it started up fine...

So I purchased a gen 2 2.3 Whipple that came with an Accufab throttle body and am getting ready to take the car to the dyno in a few weeks for tuning. I have heard numerous stories about high idle issues and cruise control not working. I do take the car on the highway for longer stints and I...

Bought this to use in my build and then went in a different direction and no longer need it. Located in Virginia Beach, VA 23464. Shipping on your dime.

I ordered Gen 3 with plan to upgrade from twin 67 to 160 mono. Still do not have my 160 as they had to "work out the bugs" on these. I am kind of nervous of being a beta tester, especially since they have had issues with the first run. Anyone running these in the wild? Any issues?

Approx. 40,000+ miles. Asking 450 dollars shipped. Car was traded in for a truck. SOLD Throttle Body 1 by Michael Pascual, on Flickr Throttle Body 5 by Michael Pascual, on Flickr Throttle Body 2 by Michael Pascual, on Flickr Throttle Body 3 by Michael Pascual, on Flickr Throttle Body 4...

Hey guys, I'm about to purchase a TVS for my cobra, just curious if anyone is running a stock ported throttle body with theirs? Im not a big fan of the chrome gt500 TB and its an extra $600-700, I could put towards cooling, idlers ect. Also will the VMP MAF and Fuel Kit be good enough? Not...

Stock Eaton with 60k miles in perfect condition. Comes with Metco 2.8 pulley+hub, stock throttle body, stock elbow, and all bolts. - $400 obo buyer pays fees and I will cover shipping. SOLD! Stock 39lb injectors with 60k miles. Worked perfectly, no issues. - $80 shipped - SOLD! Stock FPDM -...

For sale is a stock T/B & Plenum off my 04 Cobra with 50k miles. Screws included for the IAC, factory gasket still intact at plenum/blower connection. I have never separated these, and I'd much rather sell it as a unit and not separate them. However, if you only need one or the other, let me...

Just had the whipple 2.9 front feed with the 132mm elliptical TB on my 14 GT.... did anyone have tuning issues with this TB? What issues, and how were those issues addressed? TIA

Just had the whipple 2.9 front feed with the 132mm elliptical TB on my 14 GT.... did anyone have tuning issues with this TB? What issues, and how were those issues addressed? TIA

Hi all, I have a 2010 GT500 with the stock M122 and was looking for your opinions on what I can expect as far as RWHP from these following mods. The car currently has a 2.6 pulley with a dyno tune for the pulley but I am looking to add a JLT Big Air CAI, Twin 65MM throttle body, VMP inlet...

Still have a bunch of Stock 2011 GT500 parts I need to get rid of. All parts have between 4k and 6k miles on them and are in perfect condition. The car is a weekend cruiser that has never seen bad weather let alone sat outside overnight. Shipping is added to the price and I'll give whatever...

For Sale: VMP gen II supercharger 800hp kit with quick change hub. Kit includes: VMP gen II supercharger with a 2.7 pulley, VMP 67mm twin jet throttle body, ID 1000 fuel injectors, JLT 127mm big air/carbon fiber CAI, I also have the SCT X4 tuner that I will throw in for free. Sold my GT 500...

So i recently picked up a used whipple throttle body and put it on my 13 GT500 which still has the stock supercharger on it. Then i had lund tune it and the car always has a very high idle after running it hard the rpms go between 1000-1500. Lund cant seem to find anything wrong with the tune, i...

I just picked up an 04 Cobra and I'm returning the engine bay back to the stock appearance. These parts have been on the car for several years but have no more than 7,000 miles on them. I live in Northern VA. Would Rather sell local but will ship. Let me know if you have any questions or need...

Anodized blue billetflow throttlebody with "Terminator" enscribed across the top. It does have a nick in the mouth, but it is covered up by the CAI coupler when installed. Willing to ship to lower 48 states for sale price, or pick-up locally at a discount in the Dallas TX area. Text...

Packed With Power Ford Performance Parts releases the first of three Mustang GT Power Packs By Steve Turner Photos courtesy of Ford Motor Company Owners of 2015-2017 Mustang GTs who have been waiting for a naturally aspirated power package from the factory can start to rejoice. Ford...

looking for an aftermarket throttle body and heat exchanger.. used please 07 Shelby gt500 3.4L whipple

Bought these with the intention of installing but I am choosing to invest in a set of ARH Long tubes instead. Both are new, unused Ford parts. $950 shipped for the pair [/URL][/IMG]