Kenne Bell 2v Thread

[kyoshosp2]

Bought a 2000 saleen. Today with 2.1 he said. Not sure pulley size gauge shows 6-7lbs, has 302 stroker,9.5 compression, ported heads and Voodoo cams. . It sure does lope. .. Bbk shorties and offroad X pipe with 3:73 gears. no power numbers either. ... Wanting to get 550-600rwhp. Can it be done with what i have? im thinking of selling 2.1 and maybe motor. .. Might go T trim and pump gas and get numbers if thr 2.1 cant do it

 

[kyoshosp2]

 

[kyoshosp2]

 

[froush]

In order to get the number you want out of the 2.1, you will need to do the inlet upgrade. That involves getting a kb inlet for a 2.2/2.6/2.8 and then you will need a spacer under the blower. This also involves a new cai, throttle body, iac valve, throttle amd cruise control cables. Then obviously you will need to pulley it down to get 18-20 psi out if it

 

[kyoshosp2]

It's has what I measured and is a 3" pulley . But KB boost gauge shows 6lbs ? Is that right ?

 

[1sikStang]

CLEAN looking ride!! I'm a sucker for white. White on white looks good.

 

[kyoshosp2]

Yea it's nice for sure my favorite color .. Came with the Ford blue decals too ..

I rode it again and gauge is hitting 9lbs when I stay in it .. What pulley is the 14# one ?

 

[kyoshosp2]

 

[Tmangt281]

2.6L, 3"sc/7.5"crank (16psi @5280), Fox Lake ported heads, MPH cams, arh 1-3/4"x 3" lt, Afco GT 500 HE with fans, Thump RRR Tensioner, E85, Nitrous.
674hp/653tq SAE
757hp/801tq SAE on 50 shot
gripper plate has since been removed and now KB dual bearing idlers in place.

Mustang Nitrous Purge - YouTube

 

[Dasaliac03]

Anyone running aftermarket idlers?

I've been looking into getting 2 smooth billet flow idlers to match my blower pulley but don't really have the room for a 90mm

 

[Tmangt281]

How about the Thumprrr idlers?
Thump RRR Idler Pulleys

 

[Dasaliac03]

How about the Thumprrr idlers?
Thump RRR Idler Pulleys

They look just like my steeda idlers from lethal. I'm thinking like the "flashy" metco or billetflow

 

[Thomasfarms]

Kb 2.1
Mine made 440 hp and 485 ft/lbs with 10psi boost.

 

[Massie02GT]

This thread is really making me rethink doing the Tork Tech build on my GT. I absolutely love the way a KB looks and you guys are making some decent numbers out of them.

 

[ponyboyisaac]

Bumping this thread, as I have a question and one of you guys might be able to answer.

I'm looking for a KB pulley for 11 psi for my 1.7kb. Anyone know what size pulley that would be?

Just want to give a small kick in the pants, ive had it at 9 psi for years now and I would mind another 15 to 20hp. Thanks.

 

[bigjeezy04]

KB 2.6 mammoth- 14lbs 3.25 pulley and 6.5 crank
38cc tfs heads with there cam (stg 2)
10.5:1-built bottom except crank
and more of course
fuel: 340stealth pump -10line & 60lb inj
trans: built 4r70w,10in 2800stall,-8line to a derale cooler
rear: 33spline,3.73,spool :bowdown:

this pic is with the 4.0 pulley

all stock :bs:

 

[froush]

Sleeper status x infinity

 

[lastmanstanding]

Bumping this thread, as I have a question and one of you guys might be able to answer.

I'm looking for a KB pulley for 11 psi for my 1.7kb. Anyone know what size pulley that would be?

Just want to give a small kick in the pants, ive had it at 9 psi for years now and I would mind another 15 to 20hp. Thanks.

You would need to go 1/4inch smaller than what you have now.

 

[ponyboyisaac]

You would need to go 1/4inch smaller than what you have now.

Thanks for the reply man.

 

[Dasaliac03]

Bumping this back up!

Heres the most current setup, KB 2.6L 3.25 pulley.

Made 520rwhp/466rwtq on the dynop with the clutch slipping like a bitch!

Swapping ou the clutch and flywheel, modding the fpdm, installing the smaller pulley and then back to the dyno we go!