Hello,
i need help.
How much weighs the new Oliver I-Beam with ARP Bolts?
Ralf
i need help.
How much weighs the new Oliver I-Beam with ARP Bolts?
Ralf
Last edited:
Question to the Oliver connecting rod
- Thread starter German Boy
- Start date
Nobody?
Sorry, I have the Oliver rods in my motor, but don't have the weight, I'm not even sure who balance my rotating assembly would have the weights. I looked it up this morning on Oliver web site but the weights were not listed, you should call them or email them Monday, again sorry. Bill
Thanks Bill,
you are my hope.:beer:
I have read your post from your Motor, I congratulation.
I can to have the Oliver Rods for $1300, that is the good price.
Ralf
When finished my Motor, i can english.:read:
you are my hope.:beer:
I have read your post from your Motor, I congratulation.
I can to have the Oliver Rods for $1300, that is the good price.
Ralf
When finished my Motor, i can english.:read:
Yes, that is what I paid for my rods, I also upgraded the ARP 7/16 WSB bolts that come with them to ARP's MP35X for a addition $400. You may ask them if they are needed for your build, I was looking for a higher rev, more boost motor. Your English is fine, I have another friend over there his name is Ralf also. Good Luck, Bill
Hey Bill,
your another friend is Ralf Kli...., or also Bandit 012?
My new motor for 93 octan:
Ford GT-Block
Oliver I-Beams?
Manley 18 Dish Pistons Skit Coated
Ported Ford GT Heads
Bronze Valve Guides
Ford GT-Camshafts
Whipple 3.4 with 3.5 or 3.25 Pulley
IW-10%Pulley
80 Injektors FRPP
BAP Dual-Kenne Bell
L&M 66 dual bore TB
MAF Housing 123mm or 125mm MAF selfmade
Air-Filter from FRPP
CAI House from 4.6 Bullitt rebuilt
HPX Sensor
Waes from Snow with 5 Gallon Tank selfmade?
Clutch?
JBA-Longtube Headders Cc.3“X-Pipe with Cats and Axle back
HE-AFCO
Ralf
your another friend is Ralf Kli...., or also Bandit 012?
My new motor for 93 octan:
Ford GT-Block
Oliver I-Beams?
Manley 18 Dish Pistons Skit Coated
Ported Ford GT Heads
Bronze Valve Guides
Ford GT-Camshafts
Whipple 3.4 with 3.5 or 3.25 Pulley
IW-10%Pulley
80 Injektors FRPP
BAP Dual-Kenne Bell
L&M 66 dual bore TB
MAF Housing 123mm or 125mm MAF selfmade
Air-Filter from FRPP
CAI House from 4.6 Bullitt rebuilt
HPX Sensor
Waes from Snow with 5 Gallon Tank selfmade?
Clutch?
JBA-Longtube Headders Cc.3“X-Pipe with Cats and Axle back
HE-AFCO
Ralf
Last edited:
You are correct again, he is a good man, if you speak to him say I said hello! Bill
i cant read that. it hurts my head.
You hurt my head!!!Bill
Info for my Dealer,
the Oliver have 620 grams.
Ralf
the Oliver have 620 grams.
Ralf
i would suggest getting custom grind cams instead of the ford GT cams. you'll get more bang for your buck since they'll be tailored to your new engine set up.
Who makes the right ones, CompCam?
I have no experience with the modular motor.
Ralf
I have no experience with the modular motor.
Ralf
I will make the next engine because I wanted to fit 94mm pistons!
Let's see how the new block is 2011.
Ralf
Let's see how the new block is 2011.
Ralf
Van@RevanRacing
Active Member
Hahaha
But then you just take pump gas out of the equation, correct?
His build sheet above said 93 octane...
:bash:
Users who are viewing this thread
