Search results

Anyone know the guy that was making the pieces to cover the trim pieces for the shifter and console for a autoswap? Can't find where to buy them.

Cobra has been parked in my garage since November and hasn't been started since. Noticed last week there was a small amount of coolant under it toward the rear of motor. Just a few drops. Got under and could see a small drop forming on the bottom of the bell housing. Any ideas where this is...

Ready to install id1000s on my Cobra and was assuming I had to pull the blower to do so. Had a friend tell me I could do it without pulling the blower. 2.9 Whipple standard inlet with Fore rails. Anyone ever do this without pulling the blower?

Anyone use any Jax Wax products and if so what did you think of them?

Bought a spare set of halfshafts and the abs rings are missing. Where can I buy these and do they just press on?

Looking to get a 16" bias ply DOT tire and all is available is 26x11.5x16 M&H cheater slicks or Hoosier QTP 26x9.5x16. Any one have experience with either? Need it to hook 650whp and wondering if the 9.5 is too small? Can't find anyone who has tried the M&H bias ply.

Installed a Moroso coolant expansion tank and put the factory cap on it and it is leaking around the cap. I have read before that others have had this problem but searched and can't find the fix? New cap?

I am ready to install the drivers side head on my 03 and noticed the header gasket that the Ford guy sold me is in 2 pieces. The one that is on their is in one piece but looks the same. Is this the right piece or are they side specific?

My Cobra is lowered and was wondering if the Hoosier 28x11.5x16 QTP would fit with no issues. Car has rear fenders rolled and low pro IRS bolt. Let me know if you have run this setup.

Wondering if anyone has had any issues with the latest revision of the drivers side head. The DC casting. Had a exhaust seat fall out of my DB casting head on cyl.6 and not sure if I trust it to be repaired. I can get a new head from Ford for $1300. Also, any need to use the head cooling mod on...

Had a miss in my Cobra after a short drive and came to find out I had no compression on cyl 6. Took valve cover off and there was a cam follower just lying on the head. Everything looks fine in the head. Have Comp cams and springs and heads are stock except for a valve job. Anyone have this...

Looking for a cheap wheels for the track. Will any 16 inch from 94-04 fit my Cobra with IRS? What is everyone using? thanks

Came off my 03 Cobra vert. Approx 65k miles on them. Asking $160 shipped obo. Struts are in Canada but I have sent lots of stuff across the border without issue.

Noticed a small amount of oil in all 4 spark plug wells on my drivers side when checking plugs at the end of the season. Not a lot but a few Mls in each and a little on the coil pack boots. Anyone ever re-torque the valve cover or should I just pull it and replace doughnut gaskets and gasket?

Bought a car with an engine that was built/installed by Dynospeed in Memphis, TN. Anybody else have an engine done by them? Not sure if they assembled it or had a machine shop do it all. Car runs great and was looking for more feedback on their work.

New in box Steeda IRS brace. Bought Ford Racing cover so no longer need. Asking $120 shipped.

Bought this car with all the work done to it and the PCV system looks a little different. There is gunk getting in to my intake so going to add JLT separator but it looks like it is routed a little different than others I have seen. Line comes from drivers side valve cover which has a PCV valve...

Took the car for a ride today and got into boost a couple of times and car was pulling great. Air was cool and car was liking it. When I got home and popped the hood the was a small bead of coolant around the cap of my LFP inter cooler tank where the metal ring bolts on to the tank. Bought the...

When backing my Cobra into my garage over the last three weeks I noticed that the brake lights were staying on. Figured out it is the switch that is on the upper part of the brake pedal lever. First time it happened I just jiggled the switch and it went off. Today however, it wouldn't turn them...

Took the car for a spin today for the first time since November and noticed the fog lights aren't working. The light on the button won't light either. It was working fine when I drove the car before I put it in storage. I did have the shifter bezel off last week to install a firewire cable so I...

Boost gauge isn't working and the guy I bought the car said it just needed a new vacuum line. He said it was the one in the engine bay. I can see a plastic nipple on the drivers side firewall that looks like it should have a hose on it but no clue where it goes to? Any pics/help would be...

Got this when I bought my car as the guy had already purchased it but never had it installed. Anybody ever heard of it or used it? Wanted to buy the FTBR kit but already have this stuff here and paid for. Let me know what you guys think.

Have a Innovate wide band in my 03 Terminator and it will work for a minute or 2 then the gauge goes to 21.9, stays there for a few seconds then starts flashing 7.4 until I restart the car. Tried to contact Innovate directly but the info they sent me is confusing. Anybody else ever have this...

Looking to get into a Terminator and have found a car that I am interested in but am worried about the fuel system. The car made 633 rwhp on 94 octane and the guy says he is only running 60 injectors with the stock fuel pumps. The car is a 2003. He says he installed the KB BAP and it did nothing...