the days of Corbic's livesThis soap opera that I don’t believe 1/4 of is still going? If it’s true, you should have dumped that car forever ago. JMO.
Pretty sure I posted that before.
the days of Corbic's livesThis soap opera that I don’t believe 1/4 of is still going? If it’s true, you should have dumped that car forever ago. JMO.
Pretty sure I posted that before.
It’s honestly stupid at this point. Again, just my opinion.the days of Corbic's lives
So you took it to PHP huh?
How long did it take for him to get it in and what kinda turnaround was he talking about?
I got ya, I was just curious. I'm picking one up soon and was looking for someone to give it a good look before I start driving the shit out of it.I’m in no rush.
View attachment 1516139
Sooooo she’s back from PHP. Picked her up last Thursday, сука блять.
Here’s what is know, done and needs to be done.
Issues -
KB 2.2 is very loud, maybe dead but did not remove to inspect.
Pulleys, lots of wear and tear
4lb lower, S/C has been spun way to high way to long.
Radiator Fan is constantly running.
Rear End is loose.
-
Transmission, pulled and inspected. Fluid was full of bearing material. The issue is the clutch was not aligned and installed properly. Someone used lock washers to space it out.
Adjustable Quadrant was not installed correctly.
Essentially the clutch was putting downward pressure on the input shaft and slowly destroying itself.
Remedy :
Sent the Clutch and flywheel our for rebuild. McLeod stated the clutch was 11-12 years old based on serial numbers.
New sealed double roller TOB, new Quadrant setup. Input Shaft bearings.
Drive shaft was also worn out, replaced with Like New - Used unit.
All told, $2,800.
I have about 150 miles on the car now (120 driving home). It drives significantly better. A slight whine in some gears, but it shifts buttery smooth.
Washed and Waxed this weekend. I’ll get some photos up later.
I cleaned the engine and it looks like one of the overflow lines on the SC has a slight leak. I’ll reseal that.
plans? Sell it?
Rear end + blower wont be cheap to fix....
No idea.
Rear won’t be an issue. I had Belle Tire align the car and apparently they didn’t torque the adjustments in the rear.
The URCA also have a 10mm bolt and heim, however the chassis is 12mm. That needs changed out.
Blower wise. I’m in limbo. Rebuilding the 2.2 is going to be +$2k. I’ve yet to see one of these $1,000 trade in 2.3s (jokes) and by the time I’m ready to move on a 2.3, I’m sure they’ll be sold out.
I bet I can sell the KB for $1k even blown.
I can also scorer about for a used Eaton, but I run the risk of wasting $400-800 on a burned out turd as well.
Car also needs paint correction. Soooo yeah.
if it were me, I'd rebuild the 2.2.
Yeah I know, wont make the power and OMG VMP Gen 3 omg omg omg omg
But nothing beats the scream of a 2.2. Period.
#15yearoldracecarlife
ftfy, went through the ringer with both of my cars, not to the extent you have, but neither were as advertised.
Just gotta fix it up right and keep it moving, but if I had your car, I may have cut my losses already....
are they definitely going to stop offering the 2.3 some time soon?
shit.
i was just looking at vmp a couple days ago. the 2.3 kit was $1k less than the 2.65...was looking forward to grabbing a new one some time LOL.
Did some research last night.
Looks like the KB can be rebuilt by Jon Bond for around $1k w/ shipping. So that, plus some new pullies ($400) and I may be back in the game. Since there is only about 4 weeks left in the season, I'll just hold off till January to do anything.
Also, if I get it rebuilt, I could hit two birds with one stone and get a different pulley installed on the blower. It spins to 21psi right now with lower - I want to drop that back down to 17psi I think to keep the 93oct and fry the blower again. Looking around that should be good for 575-580whp.