• Welcome to SVTPerformance!
ATTENTION!
You may experience intermittent issues while accessing the site over the next 60-90 minutes, as we perform maintenance and upgrades.

2013 Steeda Big Bore intake ?

Discussion in '2013-14 Shelby GT500' started by spazpilot, Jun 23, 2013.

  1. spazpilot

    spazpilot New Member Established Member

    Messages:
    150
    Joined:
    Sep 4, 2010
    Location:
    Carrollton, TX
  2. Carl

    Carl New Member Established Member

    Messages:
    209
    Joined:
    Jun 10, 2008
    Location:
    Maine
    Somehow I doubt their stated power gains from the CAI and tune.
     
  3. Crowley

    Crowley Okey doke Established Member

    Messages:
    4,270
    Joined:
    Sep 21, 2003
    Location:
    Texas
    I don't think you will get those gains, but the BLUE filter is a plus!!!

    Crowley
     
  4. Van@RevanRacing

    [email protected] Authorized Vendor Authorized Vendor

    Messages:
    6,964
    Joined:
    Feb 24, 2008
    Location:
    S. Florida
    S&B makes a blue filter that will fit perfectly on the JLT intake.
     
  5. Copper&Black

    Copper&Black Member Established Member

    Messages:
    659
    Joined:
    Jun 22, 2012
    Location:
    FL
    Ask Devious Snake, he runs that CAI. He likes it from what I understand.
     
  6. LT5

    LT5 New Member Established Member

    Messages:
    69
    Joined:
    Jun 21, 2012
    Location:
    CA
  7. USV8PWR

    USV8PWR Member Established Member

    Messages:
    892
    Joined:
    Mar 10, 2012
    Location:
    Austin TX
    The best looking, most factory looking, CAI out there IMO. And I love the pics of it installed on Devious' car on that website. :rockon:
     
  8. GOTSVT?

    GOTSVT? This Is Absolution Premium Member Established Member

    Messages:
    13,225
    Joined:
    Mar 16, 2006
    Location:
    1320
    Anyone make a white or black airfilter
     
  9. Crowley

    Crowley Okey doke Established Member

    Messages:
    4,270
    Joined:
    Sep 21, 2003
    Location:
    Texas
    Yep .. looks good.

    Crowley
     
  10. 09Troublemaker

    09Troublemaker " That don't sound stock" Established Member

    Messages:
    6,317
    Joined:
    Dec 9, 2008
    Location:
    Long Island, N.Y.
    +1

    I've read good things about this unit
     
  11. Devious_Snake

    Devious_Snake PSR Major! Established Member

    Messages:
    9,980
    Joined:
    Dec 25, 2011
    Location:
    Hell
    The gains posted are accurate, I would know they are from my car!

    The intake is fine piece, I am running the prototype model. Fitment is good, the enhanced sound from supercharger is a plus! It looks good, no issues thus far using the ram air tube with the heat shield. I have run the car up past 150. The power gains are very noticeable, my car was putting down 660 with the pulley/intake/tune only on their dyno ( base was 580ish)

    I would recommend this unit as a great alternative to the other popular models out there. I have been running it for a couple months now and have ran the car hard. No issues and I have given them feedback on any improvements that can be made.
     
  12. spazpilot

    spazpilot New Member Established Member

    Messages:
    150
    Joined:
    Sep 4, 2010
    Location:
    Carrollton, TX
    Devious
    Thanks for your input. I've been looking at it mainly because I notice it doesn't require me bending that hood cable tab. My main concern on this one is how close is the MAF harness to the body, if it rubs, and if the final product on the breather tub still requires the hose clamps with a piece of hose or if they fixed it to a grommet push in like the factory one.
     
  13. tj@steeda

    [email protected] Member Established Member

    Messages:
    474
    Joined:
    Oct 13, 2011
    Location:
    Detroit
    Thank you, Devious_Snake.

    Your input is greatly appreciated.

    Best Regards,

    TJ
     
  14. Devious_Snake

    Devious_Snake PSR Major! Established Member

    Messages:
    9,980
    Joined:
    Dec 25, 2011
    Location:
    Hell
    We adjusted mine so there is clearance from the maf to the body. as far as the breather tube, it might be changed. Like I said mine was the prototype. I don't have those specifics for you sorry. It did take a few tries to get the mold and shape right so thats why the fit looks damn near perfect.


    Just FYI for everyone, my contact at Steeda is Matt Levine out the pompano beach location. If you want to order, be sure to hit him up and mention me to him. Also the Intake, Shifter and Pulley should be available now. 954-960-0774
     

Share This Page