Search results

Anybody have inner fenders for 1967-1972 ford truck, or know of a parts truck around east tennessee anywhere?

2003 GSX1300R Hayabusa Custom Paint, Full Titanium Akropovic Race Exhaust, Carbon Fiber Mirrors, Clear front turn signals, Carbon Fiber rear signals, Undertail, Gel Seat, Billet Bar ends, 6000 miles. 7,500 obo. Email for pics [email protected]

For you guys that have done it or priced it. Approx, what is the cost to purchase and have cams installed with supporting mods. Thanks, Dave

If you lengthen the tubes in the PCV system substantially to install oil separators, does it cause a problem as far as the computer metering the air in the system?? Will it throw a code?

Any body have the phone number for Modular Madness? Thanks, Dave

Who has used it and how user friendly is the software. Thinking seriously about going this route. Thanks, Dave

KB guys. What timing are you running at WOT with your KB set-ups? I am planning on 17psi with 93 octane. I have a 4 lb Metco lower set-up to kick it up to 21psi but I just do not want the extra fuel expense. Thanks, Dave

Anyone Musicians interested on a couple of vintage Professional Model saxophones? This is what I have. Send Email for details and pictures. Dave Buffet Crampon Super-Dynaction Tenor sax. Professional Saxophone. Made in 1972. Almost mint. Original Lacquer 99%. Many new pads a while...

Anyone had luck with compounding some of the orange peel out your paint by hand? Considering giving it a try.

Why have most seemed to have abandoned autologic chips? Are the newer options from SCT and Revolution that much better?

Went and drove a 04 Cobra the other day. Thinking of trading for a black one. The car had fourteen miles on it and a little over twenty after I drove it. During the test drive I pulled into a parking lot so the fiancé and me could look at the paint in the sun and just look the car over real...

Where is the best place to get an aftermarket mass air meter calibrated to 60# injectors? I don’t want to have to fool with the whole tuning around the stock one deal. I am using an Autologic chip so the new one from SCT will not work from what I understand.

Can you put a QUD2 computer from a 03 into a 04 that originally had an YDH1 computer in it and everything run right?

Just had Nitto’s installed on all four corners last week. Took the car for about a four hour round trip the next day after getting the tires, and everything seemed normal. This past weekend on the way to Pigeon Forge I noticed a vibration cruising at 80mph. I turned off the radio, put the car...

Need to find an Autologic tuner near East Tennessee for KB with 60# injectors. Anybody know of an experienced one. If not, taking suggestions on where to get my car dyno tuned. Thanks, Dave

Where is the best place to buy new 55lb injectors?

Kenne Bell Oval, or BilletFlow for use on a Blowzilla. What do you guys think?

Is it possible to change the inlet after the KB has been installed on the car? Trying to decide whether to go with the stock TB or a single blade TB.

When adding boost what is the rule of thumb for tuning as far as timing retard and fuel percentage increase per pound of boost added?

Are the Nitto 315/35/18's bad to pick up rocks and debri and sling them on the car during normal driving condition. I am sure they will whem heated but just on a cruize how bad would they be?

I have an autologic chip that does not have the switch on it. It has about four inches of the wire leads coming out of the chip. Where can I get a switch so I can have more than one tune and be able to switch from program to program. Is it a special switch only from the manufacturer, or can...

The Harvard Bridge and the Longfellow Bridge are one mile apart. The MIT crew team starts rowing upstream at the Longfellow. As the crew passes under the Harvard, the coxswain’s neoprene visor falls into the river. Exactly 10 minutes later, the coxswain notices, turns the boat around...

Who sells a lowering spring kit that will drop my car but keep the factory stance where the back is a little higher than the front. I like the back to be up just a tad. I think the stance looks good now but I would like it a little lower.

Some one with dyno knowledge on the 03’s help me out here please. These are back to back runs right after installing a 4lb lower to go along with my 2.93 upper. I had some belt slip going on I believe at the time but could it have been some spark blow out as well. On the first run you can see...

A few of my friends and I from highperformancetoys.com got together Saturday and took a few pics.