Search results

Does anyone know of a good shop in South Florida to do a rear gear swap? I'm in the Boynton Beach area. Thanks - jim

In all the posts I've read people are replacing the upper control arm but nobody mentions replacing the diff bushings. It looks like all the different upper control arms come with the front bushing (poly) but what about the rear? Is it just implied or is everyone leaving the stock diff...

Does anyone know if the 07-09 blocks have knock sensor bosses? Does the 07-09 wiring harness have wiring for knock sensors? If not is it a small enough section of harness that can be purchased from Ford? I know the PCM hardware is the same, its just a different flash. Has anyone put the...

If I go to www.svtperformance.com I get a blank page. I have to go to www.svtperformance.com/forums to get anywhere in the site. Anyone else have that problem? jim

I posted this in the Engine forum but I'm not sure if I'll get as much of a response there. Has anybody ever data logged the iat1 and iat2 temps after installing an aftermarket heat exchanger? I still have the factory HE. Half way through 4th gear iat1 is 92 degrees and iat2 is 141. Do...

Guys with aftermarket HE, I have a question for you Has anybody ever data logged the iat1 and iat2 with an aftermarket heat exchanger? I still have the factory HE. Half way through 4th gear iat1 is 92 degrees and iat2 is 141. Do the aftermarket HEs do any better? You can see how the...

I know I can just pull the wheel and try to measure, but it's my only car so it seems like a PIA to use the trial and error approach if someone knows. I want to retorque the axle nuts. I'm talking about the outer nut where the half shaft comes through the hub. I had the car at the dealer to...

TSB 03-9-5 from MAY 03 Suspension - Rear Suspension Clunk/Pop Noise I had it but I lost it. I was going to try and do it today to see if helped stopped the click which has been getting worse. jim

Incase you couldn't guess, I just finished installing my 2.84 pulley with a Steeda idler. I went to NAPA for a 74" belt which is what everyone seemed to recommend. I didn't want a gatorback belt, I don't want the extra noise. I want it to sound as stock as possible. They only had 73.75" so I...

I received my DJ Wideband Commander from Xtreme last week and installed it yesterday. Here are my first impressions. First, the intructions leave a little to be desired. I received 2 cables that were not listed in the instructions. One was a short peice that had a 9v battery connectot on...

Is there an advantage to an entire catback system over just free flowing mufflers? I want it to look as stock as possible so I wouldn't get the rolled tips or anything. I went to a local muffler shop and they recommended just doing the mufflers. I was thinking that they would know, but they...

Warning -- the pictures are big http://www.inductionconcepts.com/forums/showthread.php?threadid=802 Induction Concepts is making a twin turbo kit for 4.6 4V mustangs. He just finished one on a Mach 1 and it looks sweet! I can't wait to see the dyno sheets on this one. A kit like this...

I have a fairly loud ticking noise but I'm not sure if just a loud motor or not. A question for those who know. Can the tick be heard from the engine compartment with the hood open? I can hear it from outside the car, it's a pretty obvious sound. More on the drivers side than the...

I've got 1800 miles on my 03 and I've got a 'tink' sound coming from the rear when I first start moving after going in reverse. I know this is a common problem with the cobras so I'm not worried about it, but I would like as much info as possible to take with me to the dealer. Any TSBs or...

These are pictures taken of my car on a lift after my Global West subframe connectors were installed. I got the competitions noes that got all the way out to the rocker pinch seem because my car is a vert. The guy did a nice job of welding. I got them done at Steed's shop Florida. The guy...

I need to get a set of GlobalWest subframe connectors welded in. I'm fairly new to Florida so don't have many contacts down here. I tried going to a "Mustang" shop, who shall remain nameless, this morning but they were going to put my cra up on a lifted by the frame and let the suspension...

I'm new to the forums so let me know if this is the wrong place for this question. I just got an '03 Cobra vert and need to have frame connectors welded in. I'm a transplant from Jersey and don't know who's good and who's not down here. I'm getting a set of Global West Competition full length...

I have an '03 Cobra vert and need to have frame connectors welded in. I'm a transplant from Jersey and don't know who's good and who's not down here. I'm getting a set of Global West Competition full length frame connectors and want them welded in right. Does anyone know of any good shops...