http://charlotte.craigslist.org/cto/4793282147.html
http://charlotte.craigslist.org/cto/4793282147.html
Obviously not looking for 100% show quality and 10 miles, that being said my price is listed at what it's worth and what I will take. Those of you listing a 16k terminator at 22k.. Well you...
2003 Ford Mustang Cobra Conv (478rwhp 79k miles)
Call or txt me with any questions, 704-241-1925.
All the mods were done withing the last 17k miles. was all stock prior to that. New clutch, flywheel etc also. Throw out bearing started to make noise occasionally so I replaced everything to be...
Heres craigs ad. Lot more done to car than i can remember. Everything on the car is perfect, looks more like a 30k mile car. Just had compression test done, (do not have sheet but you are more than welcome to take it to any local shop) all cylinders were withing 6.6% which is amazing for any...
Heres craigs ad. Lot more done to car than i can remember. Everything on the car is perfect, looks more like a 30k mile car. Just had compression test done, (do not have sheet but you are more than welcome to take it to any local shop) all cylinders were withing 6.6% which is amazing for any...
2 Stock 03 wheels I believe, 9" wide- 2 Hankook's 275-35-17 good tread left.
2 Reps, 10.5" wide with M/T ET-streets 295-45-17 wheels and tires have less than 500 miles.
Post or PM offers or trades.
I will ship, buyer pays shipping.
Car is located In SC ZIP- 29520
Ok, so my stance is a little high in the back and possibly low in front.
Specs.
H&R Sport Springs from Lethal (Vert Springs)
All stock ISO's in place.
MM Caster Camber Plates
Tires-Front-Hankook V12 275-40-R17
Rear-MT E/T's 295/45/17
So what would you guys do to fix stance. I was...
Ok so I had a shop put on H&R sport lowering springs I ordered from Lethal and MM castor camber plates. The front is a little lower than I thought it would be, and the rear is much much higher. Anyone ran into this. Stock Iso's all around.. Will taking out rear iso's fix this or?? bad idea??
Ok. So saying, stock k member, stock front wheels no weight reduction stock 3.55 with IRS and 6speed.
How much hp/trq to pull both front wheels off the ground?
I have MT ET's right now, can it be done with those tires or are slicks a must.
Just curious.
My buddy is thinking of trading his 2006 Porsche Cayman S - 36,439 Miles
TPC Turbo Kit installed and tuned by TPC over 14,000 just for kit.
Over 10k in Alacantra suede upgrades such as (GT3 Seats, dash, shift knob and boot and console just to name a few)
Car puts down over 453 at the wheels...
I know this might be a little vauge, but here it goes. I am debating NC State Trooper, or my Local PD. I am currently deployed overseas and have 5 years in the NC Army National Guard. I have 2 years completed from a 4 year University for Criminal Justice. Would it be a good idea to try and apply...
:mj: SO FTA, Federal Tuition ASsistance is now suspended. "until further notice due to the fiscal situation" So I am sitting here overseas with the plan of continnuing (See look at my spelling I need more school) school once I get back and it is put on hold?? Cool cut out pay 20%, start charging...
Stock is 67mm grooved correct? I have a steeda 100mm aux idler on it now brand new, soon to go on- just ordered, 2-100mm metco idlers and 90mm metco idler plus new belt right sized. Should I order a 67mm (if that's what it is) new pulley for the tensioner? Or is this not needed, as in not a...
So I have always been a clean freak but I have never owned a DA, have used many though. So this was my recent order from 2 diffrent sites.
:banana:
Porter Cable 7424XP
Adam’s Swirl & Haze Remover Polishing Pad 7"
Adam’s Fine Machine Polishing Pad 7"
Adam’s Severe Swirl Remover...
Ok guys so I have some basic mods, 2.75 upper JLT CAI, Afco DP with Fans, Mez. Intercooler pump and Aftermarket reservoir. Along with some other small stuff. Anyways I'm going to be sending my Eaton of to steig soon and getting them to do a stage 6 port and maybe some other stuff. I'm hoping to...
Ok so as some of you know I am currently deployed and putting together a little parts list for my newly bought 03 ZY Vert.. I love yellow :banana:.. anyways I have several things ready to order but I am debating doing an aftermarket blower. This is my DD it currently has a 2.75 upper. Should I...
Ok quick run down, me and buddy are both deployed we get home in about 2 months.
He bought a 06 Porsche Cayman S- TPC Turbo kit at 4.5psi. 420rwhp weight right at 3000lbs.
I bought a 03 Cobra Vert- 478 rwhp pulley lots of cooling mods etc..
Vote who would win a straight up quarter mile drag.
I just bought a 03 Cobra ZY Conv. I am deployed overseas but will be home soon so I am trying to get all my basic parts down. I have a thread started in Terminator talk with the list of mods. It has IRS brace and Poly bushing set just put on. Stock shocks springs etc. I want to lower of course...
So I am currently overseas deployed U.S. Army. Ive owned a couple cars but last DD was a 98 chrome yellow cobra, t-56 built motor novi-2000 etc.. made 478/426 not bad for my DD. Sold it before deployment. I wanted another cobra and I have always loved 03-04's Like everyone else of course...