Search results

I've been tuning on my car for months, and I just can't get it right. It's a 94 cobra. Id really appreciate a base tune from a similar car to get me started. Performer rpm heads holley systemax intake stock maf 24lb injectors comp xe264hr walbro 255 pump C&L CAI BBK tb long tubes...

I have a 03 oxford white mach 1 with 78k very clean no dents. Triax shifter, o/r h pipe, rear coil overs with 12 way shocks. Asking 12k but would rather trade for a terminator i will put cash with my car. Must be within reasonable driving distance to tulsa unless you are willing to drive here...

So I just hooked up my wideband because my truck has been running lean lately. Where did you all run your wideband wiring into the cab at?

First off, I just got a '99 Lightning on Sunday so I am new to the Lightning club. I do have a question though. The keyless remote case is broken where the key ring clips on so I'm going to lose it if I don't replace the case. My question is that I have seen some aftermarket cases that look like...

I bought this about 4 months ago, and I'm wanting to build something different, and I need a truck. Right at 34k miles on it. $15,000 firm. Mods: Liberty Built T-56 Transmission w/upgraded 26 spline input shaft, and hardend bearing retainer Spec Aluminum Flywheel Spec Clutch Heavy duty...

I have a 03/04 cobra aluminum driveshaft for a t56, shifter base, and rear pinion flange. The driveshaft is used, but I've never used it. Pinion flange is new. Shifter is in used/new condition. I will ship but id rather not. These things would be perfect for someone doing a t56 swap in a non...

I've been having some traction issues in my nitrous mach 1 and wondered if you all could give me some suggestions. It only makes 422hp/504tq so I wouldn't think traction on slicks would be such a problem. The car sprays from 3300-6500rpm and is setup on a WOT switch. So far I can't get traction...

I have an '04 Mach 1 with 4.30 gears and a Built Cobra spec t56. I'm having trouble launching on slicks. I can't keep it from bogging. I even tried launching at 7,000rpm last night and it still bogged. Any tips? I've tried letting the clutch out smooth, and I've tried dropping it. The best 60' I...

Yesterday at the track I was having trouble with the line lock working, so this morning I traced the line lock wire into the cabin and disconnected it. I then wired it to a switch that I had because I figured it had something to do with the reason why it wasn't working. Then I went to start the...

I need an off road mid pipe for my '98 GT. I will take an x-pipe or an h-pipe, although an x-pipe is preferred. I believe I can use any of the pipes from 96-04. Most I can do is $125 shipped. Be prepaid to show me a picture of what ever you are selling. Thanks

Double post.

A '99 lightning with 91,000 miles that HAS been wrecked but has a clean title. The front fenders don't line up, and the tail gate gaps are off. Has a one broken exhaust tip, a small repair on the bed that needs repainted, and the hood will need repainted because its flaking around the...

Is there any way to get decent satellite photo's from a certain time period? Is that even possible? I had a wreck in December that I didn't cause but I received the ticket for it and unfortunately I didn't have a camera on me at the time of the accident so I didn't have any proof that I did not...

Do you all get cell phone telemarketers? I just started getting them and the only place my cell phone number is listed is(was) on craigslist. I just got one yesterday wanting to help me sell my car, my car is NOT for sale. This was actually the first call I have had to my cell phone that was a...

I found a 03 cobra longblock for sale locally(no lower intake, supercharger, or accessories) for $1500. I'm considering buying the engine, however, I would need to set it up as a mach 1 since I'm not interested in going through the hassle of swapping over all the eaton parts. What all would I...

I need a 96-98 cobra crossmember and brackets. Thanks

I need a cobra T56 driveshaft, shifter, and pinion flange. Thanks

I don't have a terminator but I figured this was the place to ask since its factory termi equipment. Both of the transmissions I have are shot so I need to buy a new one. So where can I get a rebuilt t56 with warranty for the best price? Smart Parts auto has them for around $1700 to my door...

I'm currently going through College pursuing a Mechanical Engineering degree and wanted to hear from some other engineers out there. Do you like your job? What do you do? Salary decent? Thanks guys

What are some decent front rotors for the money? Something around $100 would be good. Something like a stock replacement. Thanks

Hello I'm new to this forum and I hate to start out here asking a question like everyone else but here goes anyway ;-) Will a '99 IRS hold up to 400-450rwhp? It won't be dragged often and when it is it won't be with slicks. Thanks allot