Hi all im new to the 05 and up mustang,I have a question,just bought a 05 gt and notice that when i go over small bumps in the road that it feels like the front suspension is loose or theres something loose up front.like shocks or something i dont feel anything in the steering wheel i can just...
LM1 & puller for sale
--------------------------------------------------------------------------------
LM1 w/ all accessories. Brand new, never used- $250
Billetflow pulley puller- $100
Shipping not included.
Tim L
I started early Saturday afternoon. The fronts weren't hard. Once I got to the left rear, it took some time. It also was getting dark, so I had to finish Sunday. As Sunday came, I started early. It took a little time to get the left rear in, but once I did the other side wasn't bad. The ride...
I went to get the '03 dynoed today. Got to the dyno facility (CJ Motorsports) quarter after 12. I drove the car onto the dyno (in ground) and got it strapped down at 12:30.
Mods are:
•12” K&N
•2.80” SFPH Non-Slip Pulley w/ 3 Piece Idler Set
•Predator Programmer (Custom Tune)
•Borla...
I went to get the '03 dynoed today. Got to the dyno facility (CJ Motorsports) quarter after 12. I drove the car onto the dyno (in ground) and got it strapped down at 12:30.
Mods are:
•12” K&N
•2.80” SFPH Non-Slip Pulley w/ 3 Piece Idler Set
•Predator Programmer (Custom Tune)
•Borla...
I went to Byron today (11-9-'03) to improve my previous best of a 12.77 @ 110 mph. Got there around 11:30. Watched a little bit of racing. Then went and got in the staging lanes. Made my first pass at 12:24. Came off the line at 3000 rpm. 1.98 60 FT. Missed 2nd:mad: and missed 4th:mad:. End...
I went to Byron today (11-9-'03) to improve my previous best of a 12.77 @ 110 mph. Got there around 11:30. Watched a little bit of racing. Then went and got in the staging lanes. Made my first pass at 12:24. Came off the line at 3000 rpm. 1.98 60 FT. Missed 2nd:mad: and missed 4th:mad:. End...
I went to get some baseline numbers on the '03 today. Got to the dyno facility (CJ Motorsports) at 2. Got the car up on the dyno and strapped down at 2:30. Let the car sit for a little bit. The car is basically stock except for a K&N filter and the Predator Programmer. I didn't plug the...
I went to get some baseline numbers on the '03 today. Got to the dyno facility (CJ Motorsports) at 2. Got the car up on the dyno and strapped down at 2:30. Let the car sit for a little bit. The car is basically stock except for a K&N filter and the Predator Programmer. I didn't plug the...
Hi I have a question for everyone I ran an 03 cobra last week end from 70 mph to about 110 mph and I pulled him about a car and a half, My car is all stock except for a K&N, I did'nt talk to the guy that I raced but he had a catback exhaust system not sure what else if anything. I know when...
I went to the NMRA World Finals in Bowling Green, KY this past weekend (9/26-9/28/'03) and decided to enter my Cobra in the "03 Cobra Street Tire" class. With the spare tire and jack tooken out, the car weighed with me 3800 lbs. The car is stock except for a K&N filter. I was happy with the E.T...
I went to the NMRA World Finals in Bowling Green, KY this past weekend (9/26-9/28/'03) and decided to enter my Cobra in the "03 Cobra Street Tire" class. With the spare tire and jack tooken out, the car weighed with me 3800 lbs. The car is stock except for a K&N filter. I was happy with the E.T...
I went to dyno my Cobra today with a JMS chip. I did 2 base runs with the chip off, 2 runs with the first tune, 3 runs with the second tune, and 3 runs with the third.
The base pulls started off good with a 309.2 rwhp and a 299.7 rw/tq.
Once I turned on the first tune there wasn't much...
I was wondering if these wheels would work on my '99 Cobra which doesn't have IRS anymore. Here's some info on them. For the fronts they are 18" x 9", +26mm offset with a 6.11 backspacing. For the rears they are 18" x 10.5", +27mm offset with a 6.9 backspacing.
Thanks
Tim